background image

 
 

www.max-power.com 16 

25. WARRANTY COVERAGE 
 
 

Introduction 

 
 

The purpose of this document is to set out the terms of warranty cover offered in relation to 
products purchased by the End User from Max Power or its approved network of resellers.  
This document will adhere to the following format:- 
 
Section 1  

Definitions 

Section 2 

Period of Coverage 

Section 3  

Warranty Registration 

Section 4 

Warranty Terms 

Section 5 

Warranty Exclusions 

Section 6 

Procedural Guidelines 

Section 7  

Service Centres 

 
 

1) Definitions 

Authorized Repair Number

 – The number given by Max Power on reporting a fault 

with your thruster 

 

Dealer

 – An authorized Max Power sales centre 

 

End User

 – The boat supplied with supplied equipment and the owner thereof 

 

Installer

 – The authorized centre responsible for the installation of your thruster 

 

Manufacturer

 – supplier of the equipment under warranty 

 

Pleasure Craft

 – Vessels used for owner’s personal use that have no commercial use  

(i.e  Charter boats or work boats) 

 

Resellers 

– Max Power approved distributors and dealers 

 

Serial Number

 – Number in upper right hand corner of Warranty document  

 

Supplier

 – The manufacturer (Max Power) 

 

Warranty

 – The terms and conditions that are covered by the manufacturer  

 
2) 

Period of Coverage 

 
The equipment manufactured by the Supplier is guaranteed to be free from defective 
workmanship, components and materials under normal usage conditions for a period of two 
years from the date of purchase by the End User. This warranty is transferable to 
subsequent owners of this equipment during the period of coverage. 

 
3) Warranty 

Registration 

 
Register your purchase now to receive free extended warranty coverage.  This can be done 
using one of the following methods (NB. proof of purchase must be included to establish that 
equipment is still under warranty):  
 

a) 

The quickest and easiest method to register your warranty is to fax the attached 
installation check list and warranty registration to the Manufacturer 
(Fax: +33 4 92 19 60 61) 

b) 

Mail in your warranty registration document, please ensure that you make a copy 
before sending it.  (10 Allée F Coli, 06210 Cannes-Mandelieu, France) 

 
 
 

Содержание CT35




















Отзывы: