background image

-9-

   if Autonotify = 1, UCIMAG will send the message 

TRACK DATA READY

 as soon as the card

   has been swiped. The user can then poll the data with :Tn command.

  :Jb

  - Include start (%) and end (?) characters in track data, if b=0 disable, if b=1 enable

  :RTt

  - Select Reader type (determines which card load signals to use)

     0 = swipe,

     1= half insertion using 2 sensors,

     2= full insertion,

     3= half insertion using only 1 sensor in back,

     4= half insertion using 1 sensor in front,

     5= half insertion with 2 s card load signal,

     Returns: reader status

9.3 UCIMAG Status Commands

  

:SR

  - Send reader status, its configuration

       Returns: SR:ABCI.scnde.xyz.t.<sh><sl><CR><LF>

  Where:

A=CardLoad1 signal = 0 or 1

B=CardLoad2 signal = 0 or 1

C=CardLoad3 signal = 0 or 1

I=CardInserted signal = 0 or 1

s=AutoSend configuration bit = 0 or 1

c=AutoClear configuration bit = 0 or 1

n=AutoNotify configuration bit = 0 or 1

d=direction configuration bit = 0 or 1 (1 = reverse)

e=UseStartEnd configuration bit = 0 or 1

x=Track 1 enable bit = 0 or 1 (1=enabled)

x=Track 2 enable bit = 0 or 1 (1=enabled)

x=Track 3 enable bit = 0 or 1 (1=enabled)

t=Reader Type character = 0,1,2,3 see RT command

  :ST

  - Send track status

       Returns: <LF>ST:dsercc.dsercc.dsercc.<sh><sl><CR><LF>

  Where:

d= data was detected on track

s= start character was detected

e = end character was detected

r = LRC check was passed

cc = two characters representing the hex value of byte count of track first set of

                         

dsercc

 is for track 1, second set is for track 2, and third set is for track 3

  :V

  - Send Firmware Version

Returns: Panasonic UCIMAG vx.xx Copyright xxxx

Содержание ZU-1870MA101















Отзывы: