Matrix T7XE-03 Скачать руководство пользователя страница 6

Страница: 6 / 85

CAUTION

: If you experience chest pain, nausea, dizziness or shortness of breath, STOP exercising immediately and consult a physician

before continuing.

• Donotusetheequipmentinanywayotherthandesignedorintendedbythemanufacturer.ItisimperativethatallMatrixFitnessSystemsequip

ment is used properly to avoid injury.

• Keephandsandfeetclearofmovingpartsatalltimestoavoidinjury.

• Unsupervisedchildrenmustbekeptawayfromthisequipment.

• Donotwearlooseclothingwhileonequipment.

2.2 READ AND SAVE THESE INSTRUCTIONS

This treadmill is intended for commercial use. To ensure your safety and protect the equipment, read all instructions before operating the

MATRIX T7x-03 treadmill.

When using an electrical product, basic precautions should always be followed including the following:

DANGER:

To reduce the risk of electric shock: Always unplug this equipment from the electrical outlet immediately after using and before

cleaning.

WARNING

: To reduce the risk of burns, fire, electrical shock or injury to persons that may be associated with using this product.

An appliance should never be left unattended when plugged in. Unplug from the outlet when not in use and before putting on or taking off parts.

This product must be used for its intended purpose described in this service manual. Do not use other attachments that are not recommended by

the manufacturer. Attachments may cause injury.

To prevent electrical shock, never drop or insert any object into any opening.

Do not remove the console covers. Service should only be done by an authorized service technician.

Neveroperatethetreadmillwiththeairopeningblocked.Keeptheairopeningclear,freeoflintandhair.

Never operate product if it has a damaged cord or plug, if it is working improperly, if it has been damaged, or immersed in water.

Do not carry this unit by its supply cord or use the cord as a handle.

Keepanypowercordsawayfromheatedsurfaces.

Close supervision is necessary when the treadmill is used by or near children or disabled persons.

Do not use outdoors.

Do not operate where aerosol (spray) products are being used or when oxygen is being administered.

To disconnect, turn all controls to the off position, then remove the plug from the outlet.

Connect this treadmill to properly grounded outlets only.

CHAPTER 2: IMPORTANT SAFETY INSTRUCTIONS

Содержание T7XE-03






















































































Результаты поиска

Содержание T7XE-03

Отзывы:

Похожие инструкции для T7XE-03

Бренды по названию

Популярные бренды

Matrix T7XE-03, Руководство по обслуживанию

Результаты поиска

Содержание T7XE-03

Отзывы:

Похожие инструкции для T7XE-03

Бренды по названию

Популярные бренды