Matrix T5X-02 Скачать руководство пользователя страница 25

Страница: 25 / 69

led

refereNCe deSiGNaTor

deSCriPTioN

Status

led 1

auxiliary Status led

Status

led 2

auxiliary Status led

Status

led 3

auxiliary Status led

Status

led 4

auxiliary Status led / digital to analog

output.

Status

led 5

main Status / error led

led 6

indicatesif the dC buss is energized (Voltage

Present).

VCoN

led 7

indicates if Console Voltage Supply is present.

VdSP

led 8

indicates if the dSP Power Supply is present.

down

led 9

indicates if the upper console is commanding

elevation down.

led 10

indicates if the upper console is commanding

elevation Up.

PWm

led 11

indicates if Console is commanding speed.

Speed

led 12

indicates the motor is moving via the

encoder's feedback by blinking.

1. leds 1, 2, and 3 Sequence back and forth to indicate the processor is online and operational.

2. led 4 is used as a discrete / analog signal to the upper console.

3. led 5 indicates system status / mode. Currently 3 modes are defined safe mode, stand by mode and run mode. They are defined as follows:

a) Safe mode - When the controllers safety relay is not energized and no error exists, led 5 remains off.

b) Stand by mode - When the safety relay is engaged but the system is not outputting an active PWm to the motor and no error exists, led 5 blinks off

and on at a fast rate.

c) run mode - When the system outputs an active PWm Control signal to the motor and no error exists, led 5 remains oN.

Normal oPeraTioN

8.2 mCb led iNSTrUCTioNS

CHaPTer 8: TroUbleSHooTiNG

Содержание T5X-02






































































Результаты поиска

Содержание T5X-02

Отзывы:

Похожие инструкции для T5X-02

Бренды по названию

Популярные бренды

Matrix T5X-02, Руководство по обслуживанию

Результаты поиска

Содержание T5X-02

Отзывы:

Похожие инструкции для T5X-02

Бренды по названию

Популярные бренды