Matrix T5X-02 Скачать руководство пользователя страница 12

Страница: 12 / 69

ChAPTer 4: CoNSoLe oVerLAy AND WorKoUT DeSCrIPTIoN

4.1 T5x-02 CoNSole deSCriPTioN

WorKoUT KeyS

: Simple program view and selection buttons. Press the fitness Test button to cycle through available tests.

QUICK STArT / go

: one touch Start and Quick Start.

eNTer: To confirm each program setting.

UP / doWN iNCliNe: easy information and incline selection.

UP / doWN SPeed: easy information and speed selection.

UP / doWN Time: easy information and time adjustment.

emerGeNCy SToP / immobiliZaTioN: To stop all functions and immobilize the unit. The emergency stop on this treadmill must be retu7rned to its

original position in order to allow normal operation of the unit.

SToP: ends workout and show workout summary data.

PaUSe: Pauses workout. Pause duration can be set in manager mode.

NUMBer KeyPAD

: Workout data input for workout setup. Speed adjustment during workout.

Cool doWN: Puts treadmill into Cool down mode. Cood down time is dependent on the length of the workout. Workouts 19 minutes and shorter will

have a cool down length of 2 minutes. Workouts 20 minutes and longer will have a cool down length of 5 minutes.

faN: allows for fan speed selection (fan has 3 operatijng speeds).

The matrix treadmill is inspected before it is packaged. it is shipped in four pieces: the base, thye upright console supports, the handlebar, and the

console. Carefully unpack the unit and dispose of the box material.

Содержание T5X-02






































































Результаты поиска

Содержание T5X-02

Отзывы:

Похожие инструкции для T5X-02

Бренды по названию

Популярные бренды

Matrix T5X-02, Руководство по обслуживанию

Результаты поиска

Содержание T5X-02

Отзывы:

Похожие инструкции для T5X-02

Бренды по названию

Популярные бренды