background image

LK202-24-USB rev 1 

2

Table of Contents 

1. Introduction.............................................................................................................................. 4 

1.1  What it Does ..................................................................................................................................... 4 
1.2  What it Does Not Do ........................................................................................................................ 4 
1.3 Keypad Interface............................................................................................................................... 4 
1.4  Setup for Testing .............................................................................................................................. 4 
1.5  Trying Out your LK202-24-USB...................................................................................................... 5 
1.6  Trying out a Keypad ......................................................................................................................... 6 

1.6.1  Here's what to do: ................................................................................................................... 6 

1.7 Manual Override............................................................................................................................... 7 

2. Connections............................................................................................................................. 9 

2.1 Connector Pinout .............................................................................................................................. 9 

2.1.1 Power...................................................................................................................................... 9 
2.1.2 USB Communications .......................................................................................................... 10 

2.2  General Purpose Outputs ................................................................................................................ 11 

3. Displaying 

Text ...................................................................................................................... 13 

3.1 General ........................................................................................................................................... 13 
3.2  The Built-In Character Font............................................................................................................ 14 
3.3  Writing Text to the Display ............................................................................................................ 14 
3.4 Text Commands.............................................................................................................................. 15 

4. Keypad 

Interface.................................................................................................................... 17 

4.1 General ........................................................................................................................................... 17 
4.2 Connections .................................................................................................................................... 17 
4.4 USB Interface ................................................................................................................................. 18 
4.5 Keypad Commands......................................................................................................................... 18 

5.  Bar Graphs and Special Characters .................................................................................... 20 

5.1 Command List ................................................................................................................................ 20 

6. Miscellaneous 

Commands ................................................................................................... 22 

6.1 Command List ................................................................................................................................ 22 

7.  Appendix: Command Summary ........................................................................................... 26 

7.1 General ........................................................................................................................................... 26 
7.2 Issuing Commands.......................................................................................................................... 26 
7.3 On Numbers.................................................................................................................................... 26 

7.3.1 ASCII Characters.................................................................................................................. 27 

7.4 Text Commands.............................................................................................................................. 27 
7.5  Keypad Interface Commands.......................................................................................................... 28 
7.6  Bar Graphs and Special Characters ................................................................................................ 29 
7.7 Miscellaneous Commands .............................................................................................................. 30 

8.  Appendix: Specifications and Options................................................................................ 32 

8.1 Specifications.................................................................................................................................. 32 

Содержание LK202-24-USB





































Отзывы: