background image

 

Safety 

 

 

Page 5 

2.3 

General safety notices 

General safety notices are explained in this section. These safety notices are used in the 
subsequent sections. In addition to the safety aspect, you will save money and work time 
if you comply with these notices. 

Comply with these safety notices to ensure safe operation and to save work time and 
costs. 

 

In addition to the instructions in this operating manual, also comply with the generally 
valid safety and accident prevention regulations! Young persons under the age of 16 
are not allowed to operate the implement! 

 

Comply with the respective regulations for use on public traffic routes! 

 

Prior to commencing work, become familiar with all features and activation elements, 
and their function. Ensure that all protective  
devices are properly attached. 

 

The user is responsible to third persons in the work area! 

 

Do not enter the danger zone of the machine! 

 

Check the immediate vicinity of the implement before start-up. Ensure sufficient visi-
bility! 

 

Fluids (hydraulic oil) escaping under high pressure can penetrate the skin and cause 
severe injuries! Seek medical attention immediately – danger of infection! 

 

Always execute repair, maintenance, and cleaning tasks, as well as rectification of 
malfunctions with the drive switched off and the engine at a standstill. Remove the 
ignition key! After execution of these  
tasks re-attach all protective devices! 

 

For maintenance tasks with the implement lifted, always ensure that the lifted im-
plement is secured with  
suitable support elements! 

 

These safety notices are used in the subsequent sections. 

 

 
Danger! 
Severe injury to the operator or third parties occurs.  
Comply with the safety notice. 
 

Attention! 
Minor injury to the operator or third parties  
can occur. The vehicle, the mower or the environment can be damaged. 
Comply with the safety notice. 



 
Note! 
Important, helpful tips or information for the operator.  
Read this note. It facilitates your work. 

 

2.4 

Special safety notices 

Safety notices are listed in this section that are also affixed as stickers on the implement. 

Содержание MOW-H 160 CM



































Отзывы: