background image

Dimensions in Inches(millimeters)     mate.com

 

Mate Precision Technologies  •  1295 Lund Boulevard  •  Anoka, Minnesota 55303 USA  •  Phone +1.763.421.0230  •  800.328.4492  •  Fax +1.763.421.0285  •  800.541.0285

The Mate Logo is a registered trademark of Mate Precision Technologies Inc.
© Mate Precison Technologies Inc.

LIT01374 Rev B

MATE MT6AU USE AND 

MAINTE

N

A

NCE INSTRUCTIO

NS

 

Figure 1 - Upper Assembly Keying

Figure 2 - Ultra Standard

Figure 3 - Ultra XT or Original

Figure 4 - Die Carrier

UPPER ASSEMBLY:  

VFMA115315 (excludes A-station assemblies)

LOWER ASSEMBLY: 

MFMA105315

DIE CARRIER ASSEMBLY:

   N0MA00DC 

LINE-UP TOOLS:

 

VAMTALT6A

MAXIMUM MATERIAL THICKNESS: 

.236”(6mm)

MAX. TONNAGE:

 5.4 Metric, 53kN or 6 US.

LUBRICATION:

 Manual lubrication is required for all sliding surfaces 

1x week or 20,000 cycles with DTE25, DTE26, SAE-20W or similar.

iRAM compatible but not required. See your Prima Power manual for proper 
setup in iRAM machines

KEYING AND DIE INSTALLATION

1. Upper Assembly (Fig.1) offers 1 orientation key per complete A

station assembly. Different angle settings are achieved by selecting
different slots in the individual punch guides. Non-iRAM machines
rotate each station to the punching station position thus all stations
have the same angle setting configuration

a. Ultra Standard (Fig. 2): To change angle setting of punch, the

punch must be inserted into one of three internal slots of the
punch guide.

b. Ultra XT and Original Style Thick Turret (Fig.3): These guides

offer one internal slot and 2 external slots; 0°/90° and 90°/315°.

2. Die Carrier (Fig.4) offers multiple slots which accommodate the

various slot configurations of the different punch guides.

a. Install dies using a 2.5mm hex wrench for set screws

(P/N: SSS50139).

b. Torque to 4.0 N-m or 35 in-lbf.
c. After sharpenings, bring die height back to original die height of

1.187”(30.15mm) with metal shims.

Station keys are toward center

Содержание MT6AU









Отзывы: