Masterweld 321 HDP, Инструкция по эксплуатации

Страница: 3 / 30

17/03/2014 v2.2
ENGLISH
0
1 INTRODUCTION ..................................................................... 4
2 FRONT PANEL ....................................................................... 4
3 REAR PANEL ......................................................................... 5
4 INSTALLATION ...................................................................... 5
4.1 UNIT ASSEMBLY .................................................................... 5
4.2 CONNECTIONS TO THE ELECTRICAL MAINS NETWORK . 6
4.3 WIRE SPOOL POSITIONING ................................................. 6
4.4 POSITIONING THE WIRE IN THE WIRE FEEDER ................ 6
4.5 CONNECTIONS TO SOCKETS .............................................. 7
5 USER INTERFACE ................................................................. 9
6 UNIT POWER-UP.................................................................. 11
7 RESET (LOAD FACTORY SETTINGS) ................................ 11
7.1 PARTIAL RESET ................................................................... 11
7.2 TOTAL RESET ...................................................................... 11
8 SET-UP (INITIAL SET-UP OF THE WELDING POWER
SOURCE) .............................................................................. 12
COOLER ACTIVATION .................................................................... 12
REMOTE CONTROLLER SELECTION ........................................... 12
ADJUSTMENTS BLOCK SELECTION ............................................. 12
PUSH PULL ...................................................................................... 12
SELECTION OF BURN TYPE .......................................................... 12
8.1 LOCKING PROCEDURE....................................................... 13
Enabling ............................................................................................ 13
Disabling ........................................................................................... 13
8.2 TORCH LOADING ................................................................. 14
9 ALARMS MANAGEMENT .................................................... 14
AL. HEA. ........................................................................................... 14
AL. COO. .......................................................................................... 14
Err. C0 ............................................................................................... 14
Err. C1 ............................................................................................... 14
Err. C2 ............................................................................................... 14
Err. C4 ............................................................................................... 14
Err. C11 ............................................................................................. 14
Err. C12 ............................................................................................. 14
10 PARAMETERS ACTIVATION............................................... 15
Working voltage ................................................................................ 15
Welding inductance ........................................................................... 15
Wire feed rate ................................................................................... 15
Welding current ................................................................................. 15
Thickness .......................................................................................... 15
Programs .......................................................................................... 15
Hot Start ............................................................................................ 15
Crater Filler ....................................................................................... 15
3 Levels Slope .................................................................................. 15
Soft Start ........................................................................................... 15
Motor Slope ....................................................................................... 15
Bourn Back ....................................................................................... 15
Post gas time .................................................................................... 15
Pre gas time ...................................................................................... 15
10.1 WELDING PARAMETERS .................................................... 16
11 WELDING SETTINGS ........................................................... 17
11.1 MIG/MAG WELDING ............................................................. 17
11.1.1 SETTING MIG/MAG PARAMETERS (MAIN WELDING
PARAMETERS) ................................................................................ 17
11.1.2 MIG/MAG PARAMETERS SETTING (2ND LEVEL)......................... 18
11.1.3 MIG/MAG PARAMETERS SETTING (GAS MENU) ......................... 18
12 JOBS MANAGEMENT .......................................................... 19
12.1 SAVING A JOB ...................................................................... 19
12.2 LOADING A USER JOB OF FACTORY SET JOB ................ 19
12.3 DELETING A JOB ................................................................. 19
13 TORCH TRIGGER MODES .................................................. 20
13.1 2T MIG/MAG WELDING ........................................................ 20
13.2 4T MIG/MAG WELDING ........................................................ 20
13.3 3 LEVEL MIG/MAG WELDING .............................................. 20
14 TECHNICAL DATA ............................................................... 21
15 SPARE PARTS ..................................................................... 22
15.1 321 HDP ................................................................................ 22
15.2 WIRE FEEDER MOTOR ....................................................... 24
15.3 WIRE FEEDER ROLLS ......................................................... 25
16 ELECTRICAL DIAGRAM ..................................................... 26
16.1 321 HDP ................................................................................ 26
16.2 REMOTE CONTROLLER ..................................................... 27
16.2.1 RC03: ELECTRICAL DIAGRAM ...................................................... 27
16.2.2 RC04: ELECTRICAL DIAGRAM ...................................................... 27
16.2.3 RC05: ELECTRICAL DIAGRAM ...................................................... 28
16.2.4 RC06: ELECTRICAL DIAGRAM ...................................................... 28
16.3 PUSH-PULL (OPTIONAL) ..................................................... 28