manualshive.com logo in svg

MASTERPAC SG70, Руководство по эксплуатации


Поделиться
Скачать
background image

17

MAINTENANCE

3.6.2 Engine Troubleshooting

SYMPTOM

POSSIBLE CAUSE

SOLUTION

Difficult to start

Fuel is available but
spark plug will not
ignite.(Power
available at high
tension code.)

Ignition plug being bridging?

Check ignition system.

Carbon deposit at ignition?

Clean or replace
ignition.

Short circuit due to deficient
insulator?

Replace insulators.

Improper spark gap?

Set spark plug gap to
the correct gap.

fuel is available but
spark plug will not
ignite.(Power NOT
available at high
tension code.)

Short circuit at stop switch?

Check stop switch
circuit. Replace stop
switch if defective.

Ignition coil defective?

Replace ignition coil.

Fuel is available and
spark plug ignites
(compression
normal).

Muffler clogged with carbon
deposits?

Clean or replace
muffler.

Mixed fuel quality is inadequate?

Check fuel to oil
mixture.

Fuel in use inadequate (water,
dust)?

Flush fuel system and
replace with fresh fuel.

Air cleaner clogged?

Clean or replac air
cleaner.

Fuel is available and
spark plug ignites
(compression
normal).

Defective cylinder head gasket?

Tighten cylinder head
bolts or replace head
gasket.

Cylinder worn?

Replace cylinder.

Spark plug loose?

Tighten spark plug.

Содержание SG70
























Отзывы:

Нет отзывов

Похожие инструкции для SG70

Makita XGT GRV01 Instruction Manual preview
XGT GRV01
Бренд: Makita Страницы: 28

Бренды по названию

Популярные бренды

Загрузить еще бренды