MasterForce 241-0746 Скачать руководство пользователя страница 8

8

  Do not use the circular saw near fumes or combustible liquids.

  Never slow the blade down with your hands, or by applying pressure to 

the side of the blade.

  Never apply force! Move the circular saw forward gently and steadily.

UNPACKING

 

WARNING: 

If any parts are broken or missing, DO NOT attempt to plug in 

the power cord or operate the saw until the broken or missing parts are re-

placed. Failure to do so could result in possibly serious injury.

 

WARNING: 

Do not attempt to modify this saw or create accessories not rec-

ommended for use with this saw. Any such alteration or modification is misuse 

and could result in a hazardous condition leading to possibly serious injury.

 

WARNING: 

To prevent accidental starting that could cause serious per-

sonal injury, always disconnect the tool from the power source when assem-

bling parts.

UNPACKING

This product has been shipped completely assembled.
1.    Carefully remove the tool and the accessories from the box. Make sure that all 

items listed in the packing list are included.

2.    Inspect the tool carefully to make sure that no breakage or damage occurred during 

shipping.

3.    Do  not  discard  the  packing  material  until  you  have  carefully  inspected  and 

satisfactorily operated the tool.  

4.    If any parts are damaged or missing, return the product for replacement.

PARTS LIST (Fig. 1)

Fig. 1

1. 7-1/4-in Hypoid Circular Saw with Saw Blade

2. Edge Guide

3. Blade Wrench

Содержание 241-0746





























Отзывы: