manualshive.com logo in svg

MasterCraft 062-3425-4, Инструкция по эксплуатации, Страница: 12 / 16

Поделиться
Скачать
MasterCraft 062-3425-4 Скачать руководство пользователя страница 12

model no. 062-3425-4  |  contact us 1-800-689-9928

12

INSTALLATION INSTRUCTIONS

This pump is pre-wired at 
230 V. If the power source is 
115 V, remove the electrical 
housing cover. Flip the switch 
to 115 V. Replace the cover.

13

14

To prime, remove both:
a.  The plug from the top of the 

discharge tee (water will be 
filled in here); and 

b.  The priming plug in front of the 

discharge tee (this is to allow 
air to vent out while priming).

Fill the discharge tee with water 
until water overflows.
NOTE: 

It may take several minutes or more 

to fill the pipes and the pump (A) completely. 

Watch the water level in the discharge tee. 

Make sure the water level is stable and there 

are no air bubbles.

WARNING:

 If the pump is lower than the 

suction pipe, air may trap in the pipe. The 

pump may not work properly. Make sure the 

pipe slopes away from the pump.

Wrap the discharge tee plug and 
priming plug threads with thread 
tape and re-attach to the pump (A). 
Tighten with wrench.

NOTE: 

All electrical work should be 

performed by a licensed electrician.

115

230

Содержание 062-3425-4

















Отзывы:

Нет отзывов