MasterCraft 062-3420-4 Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 20

MasterCraft 062-3420-4 Скачать руководство пользователя страница 15

headline bars

continuation tabs

notes

warnings

15

headline bars

continuation tabs

notes

warnings

OPERA

TING INSTRUCTIONS

PLUG IN THE PUMP

ADJUSTING THE FLOW

WASHING MACHINE USE

AFTER the pump is completely installed, plug the
switch into a GFCI-protected, properly grounded
outlet. Plug the pump into the back of the switch’s
plug.

The drain pump can pump up to 21 gallons per minute (GPM)/ 79.5 litres per minute (LPM). Normal
sink drains allow only 5 to 6 GPM (19 to 22.7 LPM) to flow. Adjust the discharge ball valve (C) as
follows so that the pump does not cycle on and off when the faucets are on full.

• Run water into the sink. The pump will start when it detects water.
• Check for leaks. If leaks are found, unplug the pump power cord and fix the leaks before

proceeding.

• Put a stopper in the drain and allow the sink to fill up a few inches.
• Open the discharge ball valve (C), open the faucets, and remove the stopper to drain the sink.
• The pump will start. Adjust the discharge ball valve (C) until the pump runs continuously while

the faucets are running and the sink is draining. If the water level rises with the pump on, slightly
open the discharge valve to balance the flow. If it drops, slightly close the discharge valve.

Washing machines usually discharge

more water than the faucets do, and it is
normal for the water level to rise in the
sink while the pump is discharging. Do
not adjust the discharge valve to match
the flow when the washing machine
discharges into it, unless the sink is ONLY
used for washing machine discharge.

Figure 3: Pump Removal

† For easier removal for servicing or cleaning, install a
1 1/2” (3.8 cm) solvent union in the drop pipe.

NOTE:

• Washing machine discharge water contains fibre and lint. Unfiltered washing machine discharge could plug

the pump and require pump disassembly for cleaning. To avoid this, install a lint trap or bag type filter in the
washing machine discharge line and clean it out regularly.

1 1/4" (3.2 cm)

Union Half

1 1/4" (3.2 cm)

Half

GFCI Outlet

«
...
13
14
15
16
17
...
»

Содержание 062-3420-4





















Отзывы:

Нет отзывов