03. Within 15 seconds, press DOWN 8 times (briefly and quickly).
The motor performs 3 downward movements.
04. Within 15 seconds, press DOWN 6 times (briefly and quickly).
The motor signals current setting (from 1 to 5 movements).
05. Press UP, briefly and quickly, the number of times equal to the desired
setting (from 1 to 5)
06. Wait 10 seconds.
The motor signals new setting (from 1 to 5 movements).
01. Bring the motor in the lower position
02. Disconnect power supply, wait a few seconds; connect power supply.
08.2 HOW TO SET THE TILTING FUNCTION USING COMMAND BUTTONS
Wait 10
seconds
12
3
9
6
6 x DOWN
ON
8 x DOWN
Press UP from 1 to 5
times (see table)
08. TILTING FUNCTION
This feature can be useful for example in the handling of venetian blinds. Enabling this feature you can move the motor
in small steps (tilting), allowing the orientation of the slats using the command buttons or using the transmitter. You can
set the duration of the movements of orientation (see table). The factory sets the function at 1 (000 msec = inactive).
10.1 UTILIZZANDO IL TRASMETTITORE (solo Atom e Leg)
ARCO
FLUTE, KUADRO, KORT
VISIO
Other transmitters...
01. Bring the motor in an intermediate position
02. Press MENU for about 5 sec, until «rS»
appears on display
03. Press 1 time PREV / 2 times NEXT.
«12» appears on display
04. Press STOP. The motor signals the current
value (1 to 5 movements)
05. Press NEXT the number of times equal to
the desired setting (1 to 5)
06. Press STOP. The motor signals the new
value (1 to 5 movements)
01. Bring the motor in an intermediate position
02. Holding down STOP, press PROG for about
1 sec, until LEDs light
03. Press 1 time UP / 2 times DOWN.
04. Press STOP. The motor signals the current
value (1 to 5 movements)
05. Press DOWN the number of times equal to
the desired setting (1 to 5)
06. Press STOP. The motor signals the newt
value (1 to 5 movements)
01. Bring the motor in an intermediate position
02. Press MENU, «Menu rx» appears on
display
03. Press 1 time PREV / 2 times NEXT.
«12» appears on display
04. Press STOP. The motor signals the current
value (1 to 5 movements)
05. Press UP the number of times equal to the
desired setting (1 to 5)
06. Press STOP. The motor signals the new
value (1 to 5 movements)
See the User manual of
the transmitter at
section:
«RECEIVER MENU -
Function 12 -
Orientation»
08.1 HOW TO SET THE TILTING FUNCTION USING A TRANSMITTER
Command buttons
ARCO
FLUTE, KUADRO, KORT, VISIO
Other transmitters...
Press a button (less than 0.5 sec), then press it
again and hold it until you reach the desired
orientation.
Use the dedicated buttons LEFT and RIGHT
orientation.
Press STOP quickly twice and hold down UP or
DOWN.
See the User manual of
your transmitter
08.3 HOW TO COMMAND THE TILTING
1
OFF
2
050
3
100
4
150
5
200
N° of movements
Setting (ms)
09. FAVORITE POSITION
09.1 USING A TRANSMITTER
To memorize:
01. Bring motor in the favorite position
02. Press together STOP and FOR ME for
5 seconds.
03. Motor performs a signal.
To recall:
01. Press FOR ME
ARCO
To memorize:
01. Bring motor in the favorite position
02. Press briefly STOP 6 times and then
hold DOWN for 5 seconds.
03. Motor performs a signal.
To recall:
01. Press STOP 3 times (briefly)
FLUTE, KUADRO, KORT
To memorize:
01. Bring motor in the favorite position
02. Press briefly STOP 6 times and then
hold DOWN for 5 seconds.
03. Motor performs a signal.
To recall:
01. Press FOR ME
VISIO
Consult the manual of your transmitter in
the section about the functions
associated with the buttons.
Other transmitters...
To memorize:
01. Bring the motor in the favorite position
02. Press briefly DOWN 6 times
To recall:
01. Press briefly DOWN 2 times
09.2 USING COMMAND BUTTONS
6 x DOWN
2 x DOWN
To memorize favorite
position
You can memorize and recall a particular position (favorite position) both via command buttons (only when used in PULSE mode) and transmitter. When the favorite position is
invoked, the motor goes down to reach the lower limit switch, then goes up to reach the memorized intermediate position.
10. RESET
10.1 USING A TRANSMITTER
ARCO
FLUTE, KUADRO, KORT
VISIO
Other transmitters...
01. If possible, bring the motor to the intermediate position.
02. Disconnect the power supply.
03. Connect as on the diagram.
04. Connect the power supply. Wait 30 seconds, the motor makes a signal.
05. Disconnect the power supply.
06. Restore the connections (see diagram on section 2).
07. Reinstall the module (see section 3).
10.2 USING COMMAND BUTTONS
01. Bring the motor in an intermediate position.
02. Press MENU for about 5 sec, until «rS»
appears on display
03. Press 2 time PREV / 9 times NEXT.
«29» appears on display
04. Press STOP. The display flashes, the
motor performs some movement
05. Press together PREV and NEXT for about
2 seconds until the motor indicates that the
reset was performed (1 moving up / down).
06. Reinstall the motor (see section 3).
01. Bring the motor in an intermediate position.
02. Holding down STOP, press PROG for
about 1 sec, until LEDs light
03. Press 2 time UP / 9 times DOWN.
04. Press STOP. The LEDs flash, the motor
performs some movement
05. Press together UP and DOWN for about 2
seconds until the motor indicates that the
reset was performed (1 moving up /
down).
06. Reinstall the motor (see section 3).
01. Bring the motor in an intermediate position.
02. Press MENU, «Menu rx» appears on
display
03. Press 2 time PREV / 9 times NEXT.
«29» appears on display
04. Press STOP. The display flashes, the
motor performs some movement
05. Press together PREV and NEXT for about
2 seconds until the motor indicates that
the reset was performed (1 moving up /
down).
06. Reinstall the motor (see section 3).
See the User manual of
the transmitter at
section:
«RECEIVER MENU -
Function 29 -
Receiver reset»
5 poles
cable
gray
brown
blue
yellow/green
black
WARNING: This procedure restores the factory settings of the device. This procedure must be carried out by qualified technical personnel. Once the "reset" is
performed, the technician must install this device again (following the procedure on section 03. FIRST INSTALLATION) and verify proper operation.
L
N
04
To recall favorite
position
