03
05. SUN, WIND, RAIN SENSOR
The sensors generate automatic manoeuvres without notice that can be dangerous. The installer must to inform the end-user and possibly integrate the installation with adequate
security systems. In some situations (eg power loss of motor or sensor, motor failure or sensor, radio noise ...) it is possible that the command imparted by the sensor is not detected by
the motor. The sensor must therefore not be understood as a safety device which ensures the integrity of the roller in every condition, but a means to reduce the possibility that the
shutter being damaged by adverse weather conditions.
05.1 COMPATIBLE SENSORS
Use the sensor series BLAST or BLAST BT or SHAKE (wind sensor), VEGA or VEGA BT (sun/wind sensor), THANK YOU (sun sensor), X11C (rain sensor) with the power supply
AT12. When the sensor detects the presence of wind, the "wind alarm" command is sent: the tuned motors move upward and manual controls are disabled until the end of the alarm.
When the sensor detects the presence of the sun, the "presence of sun" command is sent: the tuned motors move downward. When the sensor detects the absence of the sun, the
"absence of sun" command is sent: the tuned motors move upward. When the sensor detects the presence of rain, the "presence of rain" command is sent: the tuned motors move up
or down, depending on the settings of rain sensor. Each device can store up to 4 sensors wind, only one sun sensor. For more information, consult the manual of sensors.
05.3 HOW TO ACTIVATE/DEACTIVATE THE «SUN FUNCTION» (only if a sun/sun-wind sensor is memorized)
(*) The motor signals the change with a quick movement up / down. For more information, consult the transmitter manual at section "sun / automatic lowering" function
10.1 UTILIZZANDO IL TRASMETTITORE (solo Atom e Leg)
ARCO
FLUTE, KUADRO, KORT
VISIO
Other transmitters...
01. Press SUN for about 2 seconds. (*)
01. Press together STOP and UP for 2 seconds
(*)
01. Press together STOP and UP for 2 seconds
(*)
(*)
06. TEST RADIO
06.1 HOW TO SET THE «TEST RADIO» USING A TRANSMITTER
01. Bring the motor in the upper position
02. Disconnect power supply, wait a few seconds; connect power supply.
03. Within 15 seconds, press UP 8 times (briefly and quickly).
The motor performs 3 downward movements.
04. Within 15 seconds, press UP 5 times (briefly and quickly).
The motor signals: 1 up = active, 1 down = inactive
05. To deactivate: press DOWN
To activate: press UP
06. Wait 10 seconds.
The motor signals: 1 up = active, 1 down = inactive
06.2 HOW TO SET THE «TEST RADIO» USING COMMAND BUTTONS
As soon as the module stores a wind sensor, a communication control is automatically activated between the sensor and the device. If the communication is lost for more than 60
minutes, the motor performs an upward movement to protect the blind. This automatic manoeuvre is performed every 60 minutes until the reactivation of the radio communication.
The factory recommends to keep the “test radio” active in order to identify in good time any malfunction of the radio sensor or of the radio communication.
10.1 UTILIZZANDO IL TRASMETTITORE (solo Atom e Leg)
ARCO
FLUTE, KUADRO, KORT
VISIO
Other transmitters...
01. Bring the motor in an intermediate position
02. Press MENU for about 5 sec, until «rS»
appears on display
03. Press 1 time PREV / 7 times NEXT.
«17» appears on display
04. Press STOP. The motor signals:
1 up = active, 1 down = inactive
05. To deactivate: press PREV
To activate: press NEXT
06. Press STOP. The motor signals:
1 up = active, 1 down = inactive
01. Bring the motor in an intermediate position
02. Holding down STOP, press PROG for
about 1 sec, until LEDs light
03. Press 1 time UP / 7 times DOWN.
04. Press STOP. The motor signals:
1 up = active, 1 down = inactive
05. To deactivate: press DOWN
To activate: press UP
06. Press STOP. The motor signals:
1 up = active, 1 down = inactive
01. Bring the motor in an intermediate position
02. Press MENU, «Menu rx» appears on
display
03. Press 1 time PREV / 7 times NEXT.
«17» appears on display
04. Press STOP. The motor signals:
1 up = active, 1 down = inactive
05. To deactivate: press DOWN
To activate: press UP
06. Press STOP. The motor signals:
1 up = active, 1 down = inactive
See the User manual of
the transmitter at
section:
«RECEIVER MENU -
Function 17 -
Test radio»
Wait
10 seconds
12
3
9
6
5 x UP
ON
8 x UP
To deactivate: press DOWN
To activate: press UP
07. OPERATION LOGIC OF COMMAND BUTTONS
07.1 MODIFY THE SETTING USING A TRANSMITTER
01. Bring the motor in the upper position
02. Disconnect power supply, wait a few seconds; connect power supply.
03. Within 15 seconds, press UP 8 times (briefly and quickly).
The motor performs 3 downward movements.
04. Within 15 seconds, press UP 3 times (briefly and quickly).
The motor signals: 1 up = hold-to-run, 1 down = pulse
05. To select PULSE: press DOWN
To select HOLD-TO-RUN: press UP
06. Wait 10 seconds.
The motor signals: 1 up = hold-to-run, 1 down = pulse
07.2 MODIFY THE SETTING USING THE COMMAND BUTTONS
The buttons can be operated either in PULSE logic or HOLD-TO-RUN logic.
PULSE
: to activate the motor press a button for at least 0.5 seconds, to stop the motor press briefly (less than 0.5 seconds) one of the two buttons.
HOLD-TO-RUN
: to activate the motor press a button for at least 0.5 seconds, to stop the motor release the button.
The factory sets the device to work in PULSE logic.
If the "TILTING function" is active (see section 08 "TILTING Function"), to tilt press 1 time briefly a button and immediately hold down the same button until you reach the desired
position. The FAVORITE POSITION (see section 09 "FAVORITE POSITION") is not available by the command buttons if these are set in HOLD-TO-RUN mode.
10.1 UTILIZZANDO IL TRASMETTITORE (solo Atom e Leg)
ARCO
FLUTE, KUADRO, KORT
VISIO
Other transmitters...
01. Bring the motor in an intermediate position
02. Press MENU for about 5 sec, until «rS»
appears on display
03. Press 1 time PREV / 8 times NEXT.
«18» appears on display
04. Press STOP. The motor signals:
1 up = hold-to-run, 1 down = pulse
05. To select PULSE: press PREV
To select HOLD-TO-RUN: press NEXT
06. Press STOP. The motor signals:
1 up = hold-to-run, 1 down = pulse
01. Bring the motor in an intermediate position
02. Holding down STOP, press PROG for
about 1 sec, until LEDs light
03. Press 1 time UP / 8 times DOWN.
04. Press STOP. The motor signals:
1 up = hold-to-run, 1 down = pulse
05. To select PULSE: press DOWN
To select HOLD-TO-RUN: press UP
06. Press STOP. The motor signals:
1 up = hold-to-run, 1 down = pulse
01. Bring the motor in an intermediate position
02. Press MENU, «Menu rx» appears on
display
03. Press 1 time PREV / 8 times NEXT.
«18» appears on display
04. Press STOP. The motor signals:
1 up = hold-to-run, 1 down = pulse
05. To select PULSE: press DOWN
To select HOLD-TO-RUN: press UP
06. Press STOP. The motor signals:
1 up = hold-to-run, 1 down = pulse
See the User manual of
the transmitter at
section:
«RECEIVER MENU -
Function 18 -
Buttons logic»
Wait 10
seconds
12
3
9
6
3 x UP
ON
8 x UP
Pulse: press DOWN
Hold-to-run: press UP
