Cable
motor
4 poles
SLY Cable
brown
manoeuvre 2
blue
common
yellow/green
ground
black
manoeuvre 1
fig. 1 - WITHOUT CONNECTOR
fig. 2 -
WITH CONNECTOR
03. FIRST INSTALLATION
ON
Give power supply
to the device
A
Within 15 sec press
PROG
of the transmitter
B
C
The motor moves
upward?
Press UP
briefly
YES
NO
Press PROG
of the transmitter
Press STOP 3 times
D
(1)
x3
x3
The motor signals
the end of installation
E
(1) the button must be pressed for 3 times briefly, about 1 second between each press and the next
03.1 USING A TRANSMITTER
ON
Give power supply
to the device
A
Press
the button that MOVES THE
MOTOR DOWNWARD
3 TIMES
C
The motor signals the
end of installation
D
NOTE:
It's possible to store the transmitter at a later time , following what is described in section 04.2 "How to memorize / delete a radio device using the command buttons". At the end of the
installation procedure it's possible that manoeuvres associated with the buttons are reversed.
03.2 USING COMMAND BUTTONS
Before starting the installation process, adjust the mechanical limit switches of the
motor connected to the module.
Identify the button that MOVES THE
MOTOR DOWNWARD
B
04. HOW TO MEMORIZE/DELETE A RADIO DEVICE
01. Bring the motor in an intermediate position.
02. Press PROG of an already memorized transmitter for 5 s. The motor performs 2
upward movements.
03. Within 15 seconds, to memorize/delete:
a transmitter: press STOP of transmitter you want to memorize/delete
a sensor: press «P1» of sensor you want to memorize/delete
a rain sensor: press «P2» of rain sensor you want to memorize/delete
04. 1 upward movement: device memorized!!
1 downward movement: device deleted!!
2 downward movement: error!!
PROG
(5 seconds)
NOTES:
point 03. in battery powered sensors may be necessary to keep the button pressed up to 10 seconds.
point 04. "error"is reported if the radio code is not received in time, if the receiver's memory is full, if you try to delete the only memorized transmitter, if you try to memorize
more than 1 sun sensor or more than 4 wind sensor
01. Bring the motor in an intermediate position.
02. Disconnect power supply, wait a few seconds; connect power supply.
03. Within 15 seconds, press DOWN 8 times (briefly and quickly).
The motor performs 3 upward movements.
04. Within 15 seconds, press UP 3 times (briefly and quickly).
The motor performs 2 upward movements.
05. Within 15 seconds, to memorize/delete:
a transmitter: press STOP of transmitter you want to memorize/delete
a sensor: press «P1» of sensor you want to memorize/delete
a rain sensor: press «P2» of rain sensor you want to memorize/delete
06. 1 upward movement: device memorized!!
1 downward movement: device deleted!!
2 downward movement: error!!
NOTES:
point 05. in battery powered sensors may be necessary to keep the button pressed up to 10 seconds.
point 06. "error"is reported if the radio code is not received in time, if the receiver's memory is full, if you try to delete the only memorized transmitter, if you try to memorize
more than 1 sun sensor or more than 4 wind sensor
04.1 USING A TRANSMITTER
04.2 USING COMMAND BUTTONS
STOP
P1
P2
P2
P1
STOP
P1
P2
P2
P1
8 x DOWN
3 x UP
ON
brown
blue
black
SLY Cable
1
2
3
Motor cable
Connector
already
wired
1
2
3
(common)
ground
02
