Master Therm AirMaster aku Скачать руководство пользователя страница 54 | Manualshive

Страница: 54 / 64

background image

AM, EM, AQ, BA, ASW - IOM

page: 54/64

Ing.Ji

ř

í Jiránek

5.9.4 Preheating in Accumulation Vessel of the Heating System and Electric

Afterheating

This  scheme  is  also  universally  usable  for  all  heat  pumps.  It  is  especially  suitable  for
reconstructions  with  pre-installed  electric  or  gas  heater  of  DHW.  It  is  not  suitable  for  high
demand  of  DHW.  The  DHW  is  preheated  in  the  accumulation  vessel  with  large-area  copper
heat  exchanger  to  a  temperature  nearing  the  actual  temperature  of  heating  water.
Subsequently, accumulation of through-flow afterheating to required temperature is performed.
Typical area of exchanger is 4 to 5m2. This kind of heating does not cause bacterial risk in the
low-temperature part of heating. This system requires no control, it is self-regulating.

DHW outlet

tap water inlet

electric DHW tank

optional circulation return

heat source

heating system outlets

copper/stainless steel heat exchanger 4 – 5m

2

5.9.5 Safety / PT relief valve outlet

Safety overpressure (and overtemperature) relief valve must be installed on each DHW tank.
During charging of the DHW, water leak occurs from safety valve due to water thermal volume
expansion.

Therefore draining to the waste must be provided in the area of DHW tank

installation

.

«
...
52
53
54
55
56
...
»

Содержание AirMaster aku

































































Отзывы:

Нет отзывов

Похожие инструкции для AirMaster aku

Бренд: iGenix Страницы: 6

Бренд: Panasonic Страницы: 55

Бренд: Dimplex Страницы: 4

TURBO EXCEL SO9070

Бренд: Rowenta Страницы: 44

Бренд: Reefe Страницы: 12

Бренд: Davey Страницы: 20

Бренд: CLAS Страницы: 20

Бренд: STAR Water Systems Страницы: 8

Бренд: A.O. Smith Страницы: 44

Бренд: iGenix Страницы: 9

Бренд: Yardworks Страницы: 18

Бренд: Toyotomi Страницы: 18

Бренд: ABS Страницы: 10

Бренд: NAVAC Страницы: 8

Бренд: Mosebach Страницы: 18

Бренд: HERBORNER pumpentechnik Страницы: 39

Clean Jet 800 Plus + Kit

Бренд: T.I.P. Страницы: 140

York YH9FYH12BAH-A-X

Бренд: Johnson Controls Страницы: 30

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды