Master Therm AirMaster aku Скачать руководство пользователя страница 48 | Manualshive

Страница: 48 / 64

background image

AM, EM, AQ, BA, ASW - IOM

page: 48/64

Ing.Ji

ř

í Jiránek

5.6.3 BoxAir / BoxAir Inverter multi-circuits, charging pump DHW

Universal  scheme  for  multi-circuit  heating  systems  with  accumulation  vessel.  Local  regulation
can  be  applied  here  for  100%  of  heating  output.  The  volume  of  the  accumulation  vessel  is
determined  for  15  l/kW  of  heating  output  of  the  heat  pump  for  A7W35.  Heating  of  DHW  is
provided  by  a  charge  circulation  pump  from  the  accumulation  vessel  of  the  heating  system.
Regarding  the  type  of  DHW  tank  follow  instructions  in  Chapter  “Preparation  of  Domestic  Hot
Water“.

tap water inlet / DHW outlet

DHW

venting valves

charging pump

mixing HC

venting valves

pump HC

safety valve
DN25/2.5bar

filtrball

flexible fittings

expansion vessel

heating szstem buffer with integrated manifold

DHW tank with heat exchanger

BoxAir / BoxAir Inverter machinery room for multiple circuits and charging DHW

5.6.4 Heating system charge for BoxAir and BoxAir Inverter

Antifreeze mixture of propylene glycol with freezing point -20°C is required, due to outdoor
installation. When lower (or higher) minimum ambient temperatures during winter are supposed,
adjust freezing point of the mixture.

5.6.5 Venting the system for BoxAir a BoxAir Inverter

BA units require proper venting, therefore venting valve is installed on the top of inbuild auxiliary
heater.

«
...
46
47
48
49
50
...
»

Содержание AirMaster aku

































































Отзывы:

Нет отзывов

Похожие инструкции для AirMaster aku

Бренд: Davey Страницы: 8

Бренд: Davey Страницы: 8

Бренд: Davey Water Products Страницы: 4

Бренд: Z.M. HEATERS Страницы: 8

Бренд: Calorex Страницы: 24

Бренд: Payne Страницы: 4

Бренд: SPX Страницы: 28

FIGHTER 2010 Series

Бренд: Nibe Страницы: 36

Бренд: Omni Страницы: 21

RIBILAND PRPVC1501V

Бренд: Ribimex Страницы: 35

Aquantia KHPMS-BI Series

Бренд: Kaysun Страницы: 40

Бренд: DCG Страницы: 12

Бренд: Wayne Страницы: 4

Little Giant PES-70

Бренд: Franklin Electric Страницы: 2

ELITE SUBMERSIBLE

Бренд: Hagen Страницы: 2

Бренд: SHG Страницы: 32

Бренд: TaoTronics Страницы: 13

Verderflex Vantage 3000 C R3i

Бренд: VERDER Страницы: 17

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды