background image

30

DO NOT DIVE.

103

DO NOT DIVE.

REGULAR MAINTENANCE PROCEDURES

CARE OF YOUR SPA COVER

Always cover your spa when not in use. This will greatly reduce energy consumption and will cause 
spa water to heat more rapidly. Water loss and chemical usage will also be reduced.
• Be sure to lock down all straps on cover after each use to prevent wind damage.
•  Do not allow spa to sit uncovered in direct sunlight. This may cause damage to exposed surfaces 

and components of the spa and possible discoloration of spa fittings.

•  Periodically hose off both sides of spa cover for maximum life of cover. Once a month use a vinyl 

cleaner and conditioner on the vinyl portion of your cover. Rinse residue off.

• Keep cover open for 15 minutes after adding chemicals to prevent off gas damage.

NOTE:  

if your spa is going to be left empty for prolonged periods, do not replace cover directly on 
surface of spa. Place 2”-3” blocks between cover and spa. This allows for adequate ventila-
tion of cover and spa.

NOTE:  

The cover warranty is not part of the limited warranty provided with the spa. It is provided 
through the cover manufacturer and may not be through Master Spas. Check the tags and 
labeling on your cover to verify manufacturer and refer to the manufacturer’s care, mainte-
nance and warranty information. Your dealer can help provide you with these details.

NOTE:

  To prevent premature failure of your spa cover, always turn water feature valve down so 

that the water features do not hit the cover when the cover is closed. 

CARE OF YOUR SPA CABINET

Your skirt is maintenance free. No conditioning is necessary. Simply rinse off the waterproof / U.V. 
resistant material periodically with fresh, clean water.

CARE OF YOUR OZONE SYSTEM

The ozone hose and check valve connecting between the ozone generator and ozone injector should 
be inspected and/or replaced, if necessary, every 12 months. Depending on conditions of the air 
which is being brought in to the ozone generator, the ozone hose and check valve can wear more 
rapidly. This regular maintenance is not covered under the spa warranty. Your Master Spas Dealer or 
Service Center can be contacted to schedule this maintenance. 

Note: These are areas that will require the spa owner to perform routine maintenance. These are not 
areas covered under the warranty of the spa.

Содержание legacy whirlpool

































































Отзывы: