Master Forge MFX784BDP Скачать руководство пользователя страница 13

13

Lowes.com/masterforge

OPERATING INSTRUCTIONS

Connecting the LP Tank

  WARNING: 

ALL INSTRUCTIONS AND SAFEGUARDS ON THIS PAGE MUST BE FOLLOWED 

TO PREVENT FIRE, DAMAGE AND/OR INJURY.

1.  The knob on the LP tank must be closed. Make sure that the knob is turned clockwise to a full stop. 

The cylinder supply system must be arranged for vapor withdrawal.

2. Check that the control knob on the control unit is turned 

O

 OFF.

3.  

Fold out the LP tank platform extension located on the back of the rear leg assembly (see Diagram 

1) and place the LP tank onto the platform (see Diagram 2A).

4.  

Secure the tank by 

 the retention wire onto the top of the tank (see Diagram 2B).

 

5. Remove the protective cap from the LP tank valve and coupling nut.

6.  Hold the regulator in one hand and insert the nipple into the valve outlet. Be sure the nipple is 

centered in the valve outlet. The coupling connects to the large outside threads on the valve outlet. 

Use care – do not cross thread the connection.

7.  Hand tighten the coupling clockwise       until it comes to a full stop (see Diagram 3). Firmly tighten 

by hand only. Do not use tools.

A

C

   UTION: 

In the connection process, make sure the regulator inlet connector mates with the 

cylinder valve outlet properly, safely and 

A

C

   UTION: Make sure the hose is not touching the smoker body.

Any fuel supply cylinder used must be constructed and marked in accordance with 

 

for propane cylinders of the U.S. Department of Transportation (DOT) CFR 49, or the Standard for 

Cylinders, Spheres and Tubes for the Transportation of Dangerous Goods, CAN/CSA B339. The 

appliance is to be used only with the 20-pound, vertical standing vapor withdrawal type tank and must 

include a collar to protect the cylinder valve.

A.

 DO NOT

 store spare LP cylinders under or near the smoker.

B. 

NEVER

   cylinder more than 80% full.

C. 

DO NOT 

store cylinder indoors.

 WARNING:

 ALL INSTRUCTIONS AND SAFEGUARDS ON THIS PAGE MUST BE FOLLOWED   

 

TO PREVENT FIRE, DAMAGE AND/OR INJURY.

  WARNING:

 If instructions A, B and C are not followed exactly, a 

 causing death or serious 

injury may occur.

2

1

Diagram 1

Diagram 2

Diagram 3

2a

2b

2b

Содержание MFX784BDP



























Отзывы: