background image

15

CHARGING A HOT BATTERY PACk

If the battery pack is above normal temperature range, the red LED will 

illuminate and the green LED will be off. When the battery pack cools down 

to approximately 122°F (50°C), the charger will automatically begin charging.

CHARGING A COLD BATTERY PACk

If the battery pack is below the normal temperature range, the red LED 

will illuminate and the green LED will be off. When the battery warms to a 

temperature of more than 41°F (5°C), the charger will automatically begin 

charging.

DEFECTIVE BATTERY

If the charger detects a problem, the red LED will begin flashing and the 

green LED will be off. 
1.  If registering as defective, remove and reinsert the battery pack in the 

charger. If the LED status reads “defective” a second time, try charging a 

different battery pack.

2.  If a different battery pack charges normally, dispose of the defective 

battery pack (see Maintenance section).

3.  If a different battery pack also indicates “defective,” the charger may be 

defective.

BATTERY CHARGING

If the battery pack is within normal temperature range, the green LED will 

begin flashing and the red LED will be off. The battery pack will reach a full 

charge in 45 minutes

.

 The power indicator LED lights will cycle from right to 

left during charging. This is part of the normal charging operation. 

BATTERY FULL

When fully charged, the green LED Light on the charger will be on and the 

red LED light will be off.

NOTE:

 The battery pack will fully charge, but will not overcharge, if left on the 

charger.

NOTE: 

The power indicator LED lights will not be displayed when the power 

indicator button pressed while the battery pack is still on the charger.

NOTE:

 Charger may warm with several continuous charge cycles. This is part 

of the normal operation of the charge. Charge in a well ventilated area.

Содержание 241-0416

























Отзывы: