background image

 

9

 

                Figure #5

 

 
If locking arm fails to hook locking pin, turn cam-lock counter-clockwise one completes turn and repeat the 
procedure like 

Figure #3

 

 
 
 

LEVEL FLOOR

 

 
It is very important that the existing floor be level If it is not level the insulated floor panels must be leveled by 
shimming between the existing floor and the floor panels.  Assembling a walk-in of any type on an uneven or 
unleveled floor without some sort of shimming of grouting is not practical, not advisable and will never result in 
a satisfactory installation. 
 
Leveling of floor type walk-in floor panels should be accomplished by the use of a sand leveling bed or the use 
of shim stock.  Shim stock can be rot resistant wood, strips of galvanized sheet metal, etc.  Shims under floor 
panels must be no further than 18” on center in both length and width so as to property support the floor 
panels when the walk-in is assembled and the product load is in place.  Shimming just the outer edges of just 
the corners of the floor panels will result in broken panels and/or separation of the metal liners from the foam. 
 

 
CAULKING 

 
Caulking is recommended in all panel joints as shown in 

Figure #6, #7, 

and

 #8

.  Caulk should be of high-

grade outdoor type odorless compound.  Approximately one tube of caulk is repaired for every 60 square feet 
of panel surface. 
 
It should be noted that on walk-ins subject to external weather conditions, the caulking of roof joints does not 
seal the roof against water penetration.  Therefore, a weather protective roof must be installed atop the 
insulated roof panels.   

Caulking

Roof 
panel

wall 

panel

Caulking

Joining 
seam 
of 

like 
panels

Caulking

Wall Panel

Floor Panel

 

              Figure # 6                                          Figure # 7                                                Figure # 8 

      

Roof to Wall Caulking Detail                    Like Panel To Like Panels Caulking Details                      Floor to Wall Caulking Detail

 

Содержание CL-156





















Отзывы: