background image

GB - 12

IMPORTANT: 

Check clutch/brake function 

before each use. If auger clutch bail moves 
freely with no resistance before contacting 
handlebar, adjust or repair unit before 
operating.

Primer Bulb

Push in the primer bulb to add 
fuel for easier engine start. See 

Starting and Shut Off

.

Choke Control Knob

When pulled out (away from 
auger housing) the choke 
control knob chokes off air to 
the engine for easier start. 
When pushed in, control knob 
allows for normal operation.

IMPORTANT: 

When engine has started, open 

choke slowly by gradually pushing choke 
control in.

Recoil Starter Handle 

When pulled, handle will crank engine.

IMPORTANT: 

DO NOT let handle snap back 

against unit.

Discharge Chute 

Discharge Chute rotates 220°. Rotate chute 
with discharge chute handle.

IMPORTANT: 

DO NOT force frozen Chute 

controls. Start engine and run for 3-5 minutes 
to thaw. If still frozen, take to warm place until 
controls are free.

Discharge Chute Deflector

The discharge chute deflector controls how 
high snow is thrown.
Use handle at rear of deflector to position 
deflector at desired height.
Push down handle to increase height of 
discharge.
Pull up on handle to decrease height of 
discharge.

Handlebars

Adjust upper handlebar by selecting alternate 
holes for "J" Bolts.

Tighten handlebar knobs to secure upper 
handlebar.
The upper handlebar can be folded for 
storage.

Scraper Blade

The scraper blade allows the back of the 
housing to keep better contact with the surface 
being cleared. It also prevents damage to the 
housing from normal wear.

IMPORTANT: 

DO NOT allow scraper blade to 

wear down too far or auger housing will 
become damaged.

Fuel Level Indicator

The fuel level indicator is an extension of the 
fuel tank that allows you to see the level of fuel 
in the tank without removing the fuel cap.

DANGER: 

ROTATING PARTS 

will cause serious injury or 
death. NEVER reach into 
discharge chute or housing while 
engine is running.

WARNING: 

THROWN 

OBJECTS can result in personal 
injury and/or property damage. 
ALWAYS position discharge 
chute and deflector in safe 
direction and angle before 
starting engine. DO NOT allow 
anyone in front of unit during 
operation. Be familiar with area 
of operation.

OS1620

OS1570

CAUTION: 

THROWN OBJECTS 

can cause personal injury and/or 
property damage. DO NOT 
throw snow any higher than 
necessary.
If chute deflector does not stay 
in set position, adjust as directed 
in 

Service and Adjustments

, or 

repair before operation.

CAUTION: 

Adjust auger control 

cable after changing handlebar 
height.

Содержание 938400-522



























Отзывы: