background image

PB-2100,PB-2155,PB-2200SI

21-21H-00

1

INTRODUCTION

We are constantly working on technical
improvement of our products. For this reason,
technical data, equipment and design are
subject to change without notice. All
specifications, illustrations and directions in
this SERVICE DATA are based on the latest
products information available at the time of
publication.
ECHO SERVICE MANUAL Ord. 403-11
(Model : PB-2100, PB-2110, ES-2100, ES-
2400) contains lots of information for servicing
this model.

2

CONTENTS

page

1 SERVICE INFORMATION ............................. 2
1-1 Specification ............................................... 2
1-2 Technical data ............................................ 3
1-3 Torque limits ............................................... 4
1-4 Special repairing materials ......................... 4
1-5 Service limits .............................................. 5
1-6 Special tools ............................................... 6

2 EMISSION ADJUSTMENT GUIDE ............... 7
2-1 General adjusting rules .............................. 7
2-2 Presetting idle adjust screw, L mixture needle
and H mixture needle .......................................  7
2-3 Adjusting carburettor ..................................  8

Reference No.

 

21-21H-00

I S S U E D :     2 0 0 4 1 1

INDEX

Содержание PB-2100









Отзывы: