background image

 

 

10

Transportation 

 

1.  Shutdown engine for transportation. 

2.  For transportation, tighten fuel tank cap securely and close fuel cock to prevent fuel from spilling.   

3.  Drain fuel for transportation over long distance or bad road.   

4.  Secure machine firmly to prevent it from moving or tipping.   

5.  Rammer should be transported in such position as it is placed on level ground. In case of it must 

be laid down for transportation, drain fuel tank as well as carburetor and make sure that oil plug is 

tightened securely, then tie it to the vehicle at points (a) and (b). 

6.  Direction to lay down the rammer, must be such that air cleaner comes to top. After laying it, 

make sure that there is no leak of fuel from cap (c).   

7.  Make sure lifting device has enough capacity to hold machine (see identification plate on 

machine for weight). Use central lifting point (a) when lifting machine.   

8.  Use trolley kit (supplied as optional) for short distance transportation.   

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Troubleshooting Guide 

 

A. Rammer Troubleshooting 

 

SYMPTOM POSSIBLE 

PROBLEM SOLUTION 

Engine rotates 

but amplitude 

not uniform or 

does not strike 

Operating speed of throttle 

lever is incorrectly set? 

Set throttle lever to correct position. 

Oil in excess? 

Drain excess oil. Bring to correct level. 

Clutch slips? 

Replace or adjust clutch. 

Spring Failure? 

Replace spiral spring. 

Speed of engine improper? 

Adjust engine speed to correct operating RPM 

setting. 

 

c

Содержание MR70H
















Отзывы:

Похожие инструкции для MR70H