Marvair MAA1042H Скачать руководство пользователя страница 46

Страница: 46 / 51

Marvair Wall Mount Heat Pump I&O Manual

11/2021 New

Cooling (Check and Record Readings)

After about 10 minutes of operating in the cooling mode, check and record the following data points.

Inside Temperature (IAT)

ºF

Outside Temperature (OAT)

ºF

Entering Condenser Air Temperature (Should be same temp as OAT)

ºF

Leaving Condenser Air Temperature (Acceptable Range 15º - 20º above OAT)

ºF

Return Air Temperature (RAT) db (Should be same temp as IAT)

ºF

Return Air Temperature (RAT) wb (used to calculate RH% of Return Air)

ºF

Supply Air Temperature (SAT) db (Acceptable Range 15º - 20º below RAT)

ºF

Return Air Temperature (SAT) wb (used to calculate RH% of Supply Air)

ºF

Compressor Amps (L1)

ºF

Compressor Amps (L2)

ºF

Compressor Amps (L3)

ºF

Cooling Stop

Adjust the cooling setpoint to approximately two degrees above the current indoor temperature. The

unit will sequence off, stop cooling.



Did the Compressor stop? .................................................................................................

❒

Yes

❒



Did the Condenser Fan (CFM) stop? ................................................................................

❒

Yes

❒



Did the indoor blower motor (IBM) Stop? .......................................................................

❒

Yes

❒

Electric Reheat Mode

NOTE: If the HVAC system you are testing is not configured with Dehumidification Option, Skip this

section of the Start-up / Commissioning Checklist.



Has the Humidistat Control been installed & wired to the Dehumidification input? .......

❒

Yes

❒



Has the Humidistat Control been properly setup for dehumidification? ..........................

❒

Yes

❒

Adjust the cooling setpoint so there is No demand for cooling. Adjust the Humidity setpoint so there

is No demand for dehumidification. The unit will not be running.

Electric Reheat Start

Adjust the Humidity setpoint to approximately ten percent below the current indoor Humidity

(Humidistat display should indicate current RH%). After the short delay, the unit will sequence on,

start dehumidifying.



Is the indoor blower motor (IBM) On? .............................................................................

❒

Yes

❒



Is the Compressor On? ......................................................................................................

❒

Yes

❒



Is the Condenser Fan (CFM) On? (Ambient conditions may delay CFM) .......................

❒

Yes

❒



Is the Heater On? (Clamp an AmpProbe on one leg of the heater contactor to verify) ....

❒

Yes

❒

Electric Reheat Lock-Out

While the system is still operating in “Dehumidification Mode”. Activate Mechanical Cooling.

Do Not change the Humidity Setpoint on the Humidistat. Simply adjust the cooling setpoint to

approximately four degrees below the current indoor temperature. After the short delay, the unit will

sequence on, start cooling. Notice: system did not turn off. The Only change that occurred is “Heater

turned off”.



Is the indoor blower motor (IBM) On? .............................................................................

❒

Yes

❒



Is the Compressor On? ......................................................................................................

❒

Yes

❒



Is the Condenser Fan (CFM) On? .....................................................................................

❒

Yes

❒



Is the Heater Off? (Clamp an AmpProbe on one leg of the heater contactor to verify) ...

❒

Yes

❒

Содержание MAA1042H




















































Результаты поиска

Содержание MAA1042H

Отзывы:

Похожие инструкции для MAA1042H

Бренды по названию

Популярные бренды

Marvair MAA1042H, Руководство по установке и эксплуатации

Результаты поиска

Содержание MAA1042H

Отзывы:

Похожие инструкции для MAA1042H

Бренды по названию

Популярные бренды