Marvair MAA1042H Скачать руководство пользователя страница 50

Страница: 50 / 51

Marvair Wall Mount Heat Pump I&O Manual

11/2021 New

Three Phase Units

Heater kW = (HCAL1*L1&L2) + (HCAL2*L1&L3) + (HCAL3*L2&L3)/1000 = __________kW.

Example: (HCAL1*L1&L2) + (HCAL2*L1&L3) + (HCAL3*L2&L3)

1000

Measured Voltage: L1&L2 = 241 Volts

Measured Amperage: L1 = 8.28 Amps

1995.48

Measured Voltage: L1&L3 = 243 Volts

Measured Amperage: L1 = 8.22 Amps

1997.46

Measured Voltage: L1&L2 = 235 Volts

Measured Amperage: L1 = 8.57 Amps

2013.95
6006.89 / 1000 = 6.01kW (6kW)

Outdoor Thermostat Set Point ODT

Adjust the ODT setpoint to the temperature appropriate for your application (either “Auxiliary Heat”

or “Mechanical Heat Lockout”). If you need assistance selecting the proper temperature contact tour

HVAC system designer responsible for the application. After adjusting the ODT for your application,

the HVAC system will go back to Mechanical Cooling.

Note: The range of the Outdoor Thermostat is

0ºF to 50ºF.



Is the indoor blower motor (IBM) On? .............................................................................

❒

Yes

❒



Is the Compressor On? ......................................................................................................

❒

Yes

❒



Is the Condenser Fan (CFM) On? (Ambient conditions may be delay CFM) ..................

❒

Yes

❒



Is the Heater Off? (Clamp an AmpProbe on one leg of the heater contactor to verify) ...

❒

Yes

❒

Heating Mode Stop (Mechanical Heating Heat Pump)

Adjust the heating setpoint to approximately two degrees below the current indoor temperature. The

unit will sequence off, stop heating.



Did the Compressor stop? .................................................................................................

❒

Yes

❒



Did the Condenser Fan (CFM) stop? ................................................................................

❒

Yes

❒



Did the indoor blower motor (IBM) Stop? .......................................................................

❒

Yes

❒

** If you see readings that are out of the normal range or features that seem to be operating incor-

rectly. **

Please provide a description of the issue in the Notes section below and if you need help, call:

Marvair Technical and Warranty Support: (888) 726-2734

This number is manned M-F, 8:00am to 5:00pm eastern.

Technical support calls will be returned M-F, 5:00pm to 8:00pm eastern.

Only Emergency Dispatch calls will be returned M-F, 8:00pm to 8:00am Eastern (and week-

ends & holidays).

Содержание MAA1042H




















































Результаты поиска

Содержание MAA1042H

Отзывы:

Похожие инструкции для MAA1042H

Бренды по названию

Популярные бренды

Marvair MAA1042H, Руководство по установке и эксплуатации

Результаты поиска

Содержание MAA1042H

Отзывы:

Похожие инструкции для MAA1042H

Бренды по названию

Популярные бренды