background image

 3 

 

Earth Auger safety

 

      1. Shut off the engine and be certain the drill has completely stopped rotating before inverting the 

  Earth Auger, performing maintenance on or working on the machine. 

 
      2. Make sure the Earth Auger is assembled correctly and that the drill is correctly installed and 

  securely fastened as instructed in the Assembly section. 

 
      3. Inspect the Earth Auger before each use. Replace damaged parts. Check for fuel leaks.   
          Make sure all fasteners are in place and tightened securely. Follow the maintenance instructions   
     beginning on page 11. 

 
      4. Make sure the drill does not rotate at engine idle speed. Refer to Idle Speed Adjustment, page 9. 

 
      5. Inspect the drill and replace any parts that are cracked, chipped or damaged before using the Earth 

 Auger. 

 
      6. Make sure the drill is installed and positioned correctly before using the Earth Auger. 
 
      7. Never use a drill or replacement parts that are not approved by MARUYAMA. 
     

  8. Maintain the Earth Auger according to the recommended maintenance intervals and   

     procedures in the Maintenance section beginning on page 11. 

 
      9. If running problems or excessive vibration occur, stop immediately and inspect the unit for the   
     cause. If the cause cannot be determined or is beyond your ability to correct, return the Earth Auger 

  to your servicing MARUYAMA dealer for repair. 

 

Fuel safety

 

      1. Gasoline is highly flammable and must be handled and stored carefully. Use a container approved   
     for fuel for storing gasoline and/or fuel/oil mixture. 

 
      2. Mix and pour fuel outdoors and where there are no sparks or flames. 

 
      3. Do not smoke near fuel or Earth Auger, or while using the Earth Auger. 

 
      4. Do not overfill the fuel tank. Stop filling 10mm from the top of the tank. 

 
      5. Wipe up any spilled fuel before starting the engine. 

 

6. Move the Earth Auger at least 3m away from the fueling location before starting the engine. 

 
      7. Do not remove the Earth Auger fuel tank cap immediately after stopping the engine. 

 
      8. Allow the engine to cool before refueling. 

 
      9. Drain the tank and run the engine dry before storing the unit. 

 
    10. Store fuel and Earth Auger away from open flame, sparks and excessive heat. Make sure   
          fuel vapors cannot reach sparks or open flames from water heaters, furnaces, electric motors, etc. 

 

Earth Auger Operating safety

 

      1. THIS EARTH AUGER CAN CAUSE SERIOUS INJURIES. Read the instructions carefully.   

Be familiar with all controls and the proper use of the Earth Auger. 

      2. Never allow children to operate the Earth Auger. It is not a toy. Never allow adults to operate the 

  unit without first reading this Operator’s Manual. 

 

Содержание MAG500

















Отзывы: