manualshive.com logo in svg

Maruyama BC2301RS, Руководство владельца/оператора

Поделиться
Скачать
Maruyama BC2301RS Скачать руководство пользователя страница 5

＿

 4 

＿

Fuel safety

1. Petrol is highly flammable and must be handled and stored carefully. Use a container approved  for 

fuel for storing petrol and/or fuel/oil mixture.

2. Mix and pour fuel outdoors and where there are no sparks or flames.
3. Do not smoke near fuel or Trimmer/ Brushcutter, or while using the Trimmer/ Brushcutter.
4. Do not overfill the fuel tank. Stop filling 10mm from the top of the tank.
5. Wipe up any spilled fuel before starting the engine.
6. Move the Trimmer/ Brushcutter at least 3m (10ft.) away from the fueling location before starting the 

engine.

7. Do not remove the Trimmer/ Brushcutter fuel tank cap immediately after stopping the engine.
8. Allow the engine to cool before refueling.
9. Drain the tank and run the engine dry before storing the unit.

10. Store fuel and Trimmer/ Brushcutter

 away from open flame, sparks and excessive heat. Make sure  fuel 

vapors cannot reach sparks or open flames from water heaters, furnaces, electric motors, etc.

Trimmer/ Brushcutter Operating safety

1. THIS TRIMMER/ BRUSHCUTTER CAN CAUSE SERIOUS INJURIES. Read the instructions care-

fully. Be familiar with all controls and the proper use of the Trimmer/ Brushcutter.

2. Never allow children to operate the Trimmer/ Brushcutter. It is not a toy. Never allow adults to oper-

ate the unit without first reading this Operator’s Manual.

3. Avoid using the Trimmer/ Brushcutter near rocks, gravel, stones 

and similar material that would cause  harmful missiles.

4. Keep children, bystanders and animals outside a 15m (50ft.) ra-

dius from the operator and Trimmer/ Brushcutter.

5.  If you are approached while operating the Trimmer/ Brushcutter, 

stop the engine and cutting attachment rotation.

6. Use the Trimmer/ Brushcutter

 only in daylight or good artificial 

light.

7. Never operate the Trimmer/ Brushcutter without proper guards in 

place.

8. Do not put hands or feet near or under any rotating parts. Keep clear at all times. Keep all parts of 

your body away from the rotating cutting attachment and hot surfaces such as the muffler.

9. When cutting heavy brush or small trees, always swing the Brushcutter from right to left to prevent  

kick-back.

10. Keep a firm footing and balance. Do not overreach.

11. Use the right tool for the job. Do not use the Trimmer/ Brushcutter for any job that is not recom-

mended by MARUYAMA.

No Kick-back Zone

DANGER

Kick-back Zone

Direction of 

Swing

CORRECT

INCORRECT

Direction of 

Swing

15m (50ft.)

 Minimum

Содержание BC2301RS





























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды