manualshive.com logo in svg

Maruyama BC2301RS, Руководство владельца/оператора

Поделиться
Скачать
Maruyama BC2301RS Скачать руководство пользователя страница 15

＿

 14 

＿

Hot Restart

To start the engine that is already warmed up

（

hot restart

）

.

1. Pump the primer bulb until fuel can be seen flowing through 

the fuel return line to the fuel tank. Flowing fuel should be 

almost clear, not foamy or full of bubbles.

2. Turn the choke lever to the Open 

“   ” 

position, and set the 

stop switch to the “START” (ON) position.

3. Leave the throttle trigger in the idle position and pull the 

starter grip.

4. If the engine fails to start after three to four pulls, follow the 

instructions in the Cold Starting Procedure section above.

If the engine fails to start after you follow the above proce-

dures, contact an authorized MARUYAMA dealer.

To Stop the Engine

1. Release the throttle trigger.
2. Slide the stop switch to “STOP” (OFF) position.

If the engine stops running before you turn the choke lever to 

the Open 

“   ” 

position:

Go ahead and open the choke, pull the starter grip with the 

throttle trigger positioned at Fast-idle start position.

Stop Switch

Fast-idle 

Start Lock

Fast-idle Start 

Position

START(ON)

STOP(OFF)

Idle Position

Содержание BC2301RS





























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды