Maruyama BC2301RS Скачать руководство пользователя страница 22

Страница: 22 / 28

＿

Cylinder Cooling Fins

Maintenance Interval

・

The cylinder cooling fins should be cleaned after every

25hours of operation, or once a week, whichever comes

first.

・

Air must flow freely around and through the cylinder cool-

ing fins to prevent engine overheating. Leaves, grass, dirt

and debris buildup on the fins will increase the operating

temperature of the engine, which can reduce engine per-

formance and shorten engine life.

Spark Plug

Maintenance Interval

・

The spark plug should be removed from the engine and

checked after each 25 hours of operation.

・

Replace the spark plug after every 100 hours of operation.

Spark Plug Maintenance

1. Twist the high tension lead boot on the spark plug back

and forth a couple of times to loosen the boot, then pull

the boot off of the spark plug.

2. Remove the spark plug.

3. Clean the electrodes with a stiff brush.

4. Adjust the electrode air gap to 0,6-0,7 mm.

5. Replace the spark plug if it is oil-fouled, damaged, or if the

electrodes are worn down.

6. Do not over tighten the spark plug when installing. The

tightening torque is 10,7-16,6 N·m.

0,6-0,7mm

Cooling Fin Cleaning

[Model BC2301RS, BC2601RS, BC3021RS]

1. Loosen the knob and remove the filter cover.
2. Twist the high tension lead boot on the spark plug back

and forth a couple of times to loosen the boot, then pull

the boot off of the spark plug.

3. Loosen the knob and lift off the cylinder cover.
4. Clean all dirt and debris from the cooling fins and from

around the cylinder base.

5. After cleaning, reinstall the cylinder cover, high tension

lead boot and the filter cover.

[Model BC4321H-RS]

1. Loosen the knob and remove the filter cover.
2. Loosen the knob and lift off the cylinder cover.
3. Clean all dirt and debris from the cooling fins and from

around the cylinder base.

4. After cleaning, reinstall the cylinder cover and the filter

cover.

[BC2301RS, BC2601RS, BC3021RS]

[BC4321H-RS]

Cylinder Cover

Cooling

Fins

Cooling

Fins

Filter Cover

High Tension

Lead Boot

Knob

Содержание BC2301RS





























Результаты поиска

Содержание BC2301RS

Отзывы:

Бренды по названию

Популярные бренды

Maruyama BC2301RS, Руководство владельца/оператора

Результаты поиска

Содержание BC2301RS

Отзывы:

Бренды по названию

Популярные бренды