background image

Your Room

This is an area that requires both a little background to 

understand and some time and experimentation to attain 

the best performance from your system.

Your room is actually a component and an important part 

of your system. This component is a large variable and can 

dramatically add to or subtract from a great sonic experience. 

All sound is composed of waves. Each frequency has its 

own wave size, with the lower, or bass frequencies liter-

ally encompassing from 10 feet to as much as 40 feet. Your 

room participates in this wave experience like a swimming 

pool with waves reflecting and becoming enhanced depend-

ing on the size and shape of the room and the types of 

surfaces in the room.

Remember that your audio system can actually generate 

all of the information required to recreate a sonic event 

in time, space, and tonal balance. Acoustically, the role of 

an ideal room would be to neither delete nor contribute 

to that information. However, nearly every room does to 

some degree.

Terminology

Standing Waves

Sound coming from a subwoofer bounces around in a 

room until a pattern emerges—this is called a standing 

wave. Typically, this is only a problem with frequencies 

below 100Hz. When this happens different parts of your 

room  experience either an excess or a lack of bass.

Some people believe that having a room without parallel 

walls will eliminate this effect. The truth is that non-parallel 

walls only generate different standing wave patterns than 

those that occur in rectangular rooms.

Usually, you can excite most of the standing waves in a 

room by putting the subwoofer in a corner. Listening 

position determines which standing waves you will expe-

rience. For instance, if you sit in a corner you will hear 

most of the standing waves. This can be an overpowering 

experience. Sitting next to a wall can also intensify the levels 

of the standing waves that are experienced.

Resonant Surfaces and Objects

All of the surfaces and objects in your room are subject to 

the frequencies generated by your system. Much like an 

instrument, they will vibrate and "carry on" in syncopation 

with the music, and may contribute in a negative way to the 

sound. Ringing, boominess, and even brightness can occur 

simply because surfaces and objects are "singing along" with 

your speakers.

Resonant Cavities

Small alcoves or closet type areas in your room can be 

chambers that create their own "standing waves" and can 

drum their own "one note" sounds.

Room Acoustics     17

r

oom

 a

CoustICs

Содержание Depth I





























Отзывы: