Martin Cyclo 03 Directional Скачать руководство пользователя страница 6

Страница: 6 / 36

Cyclo 03 Directional user manual

how to operate these luminaires safely, please contact your Martin dealer or
call the Martin 24-hour service hotline at +45 70 200 201.

Protection from electric shock

• Disconnect the luminaire from AC power before removing or installing a

tube or any part, and when not in use.

• Always ground (earth) the luminaire electrically.
• Use only a source of AC power that complies with local building and

electrical codes and has both overload and ground (earth) fault protection.

• Ensure that the luminaire’s live and neutral conductors are both

connected to the same RCD (ground fault circuit-breaker)

• Do not expose the luminaires to rain or moisture.
• Refer all service to a Martin service technician.

Protection from burns and fire

• Provide a minimum clearance of 0.1 meters (4 inches) around the

luminaire.

• Do not modify the luminaire or install other than genuine Martin parts.
• Do not operate the luminaire if the ambient temperature (Ta) exceeds 40°

C (104° F).

Protection from injury due to falls

• Ensure that all components and installation fittings are securely fastened.
• Ensure that all supporting structures, surfaces and fasteners can bear the

weight of all luminaires installed.

• Block access below the work area whenever installing, servicing or

removing the luminaire.

Содержание Cyclo 03 Directional





































Результаты поиска

Содержание Cyclo 03 Directional

Отзывы:

Бренды по названию

Популярные бренды

Martin Cyclo 03 Directional, Руководство пользователя

Результаты поиска

Содержание Cyclo 03 Directional

Отзывы:

Бренды по названию

Популярные бренды