manualshive.com logo in svg

Martin Yale Count AccuCreaser, Руководство пользователя

Поделиться
Скачать
Martin Yale Count AccuCreaser Скачать руководство пользователя страница 27

ADJUSTING THE RAC ROLLERS

The RAC rollers are set from the factory and it is 

NOT

 recommended to make any 

adjustments to this without consulting with Count’s tech-support department.  Should an 

adjustment be necessary, please follow the steps below. Loosen the small bearing block 

lock screws. This allows very slight adjustments of the bearing block to be made by 

loosening the thumb lock and turning the height adjustment screw in the middle of the 

bearing block. This is a very fine thread and is capable of making very slight 

adjustments. Turning the adjustment screw clockwise will increase the bar pressure, as 

counterclockwise will decrease the pressure. Once the adjustment to the bar has been 

made, slightly tighten the thumb lock and re-set the block set-screws. 

FOLDING DIRECTION OF PAPER 

There is a correct and incorrect way to fold a creased paper.  Following the diagram 

below will show you the correct direction the paper should be folded. 

Use the master groove of the base ring

to make scoring jobs with a standard

mark over all types of paper stock. 

27

CHANGING THE LOWER CREASE DIE

The Lower crease die can easily be changed to accommodate thicker stocks by removing 

the non-operator side cover, slide the bar out and flip it over to use the wider die 

channel. Please note, custom die’s are available upon request. 

Содержание Count AccuCreaser






























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды