Note: The registration is preset at the factory and should not be adjusted unless it is determined that it
is not correct for the stock being used.
Perform the following steps in order to achieve accurate registration.
1.
Loosen the thumb knobs on the paper guides for the appropriate shelf (see Figure 5).
2.
Raise retarder up using the thumb knob on the side of the machine (rotate counter-clockwise) until stock will
easily slide under retarder (Figure 7, Below.)
3.
Align register marks on layout sheets with the cutter blade edges (Figure 8).
4.
Position paper guides so that side-to-side movement will be no more than 1/32". NOTE: The guides should
not pinch the stock. Inaccurate feeding could result if too tight (Figure 9).
5.
Feed single sheets to test for accuracy. Readjust paper guides as necessary.
NOTE: You may want to use unprinted stock for initial start up to remove residual oil from cutting
blades.
Verifying a square cut:
To verify that the finished product is square, take a stack of business cards and divide in half. Flip ½ over
and recombine. All edges should align evenly. If edges do not align, the stock is skewing. See skewing section
under 6.0 Troubleshooting.
5.0 Setting Registration
Retarder
Knobs
Paper Guide
Thumb Knobs
(2 Pairs)
Figure 5
Figure 6
Stock
Retarder
Align Register
Marks with
Blades
Register Marks
(on Layout Sheet)
Blade
Figure 7
Figure 8
Paper Guide to
Stock Adjustment
Watch for Pinching of
Stock at These Points
Figure 9
3
BCS 210/212 Parts List
Item
Part No.
Description
1.
W-ODT0019
Adjustment Block
2.
M-S031092
Spring
3.
W-ODT0015
Sheet Separator
4.
W-IDT1119
Feed Bracket
6.
M-S019033
Stand Off
7.
W-ODT1123
Pressure Finger
8.
W-ODT0016
Adjust Bar
9.
W-ODT1124
Paper Support
10.
M-S032007
Knob
11.
W-ODT0014
Right Hand Guide
12.
W-ODT0013
Left Hand Guide
14.
W-ODT0011
Drive Cover
16.
M-S019033
Stand Off
17.
M-S022132
15T Pulley
18.
M-S022130
10T Pulley
20.
M-S022131
14T Pulley
21.
M-S63751563
Pulley 20XL
23.
M-S025053
95T Double Sided Belt
25.
M-S030045
Bumpers
Item
Part No.
Description
26.
M-S021073
Motor
28.
W-ODT0008
Rear Cover
30.
W-ODT0024
Receiver Tray
31.
W-ODT0023
Receiver Base Form
32.
W-ODT0021
10 Up Catch Tray
33.
W-ODT0020
12 Up Catch Tray
(not shown)
35.
W-ODT0002
Housing Assembly
38.
W-ODT0017
Slitter Shaft
39.
M-S014029
3/8 Clip Bearing
40.
W-ODT0115
Tension Collar
41.
M-ODT1105
Blade
42.
M-S031091
Blade Spring
43.
M-O200134
½" Set Collar
44.
M-S014030
½ Clip Bearing
45.
WRAOGC0026
Feed Roller w/ set screw
55.
W-ODT0107
Spacer
57.
W-ODT0022
Base
58.
W-ODT0025
End Plate
6
BCS 210/212 Wiring Diagram
