Martin Audio CDD Series Скачать руководство пользователя страница 49

Страница: 49 / 64

CDD

User Guide V1.1

CDD

USER GUIDE

APPENDIX

SPECIFICATIONS

CDD5, CDD6, CDD8

Notes

(1)

Measured on-axis in open (4 pi) space at 2 metres, then referred to 1 metre.

(2)

AES Standard ANSI S4.26-1984.

(3)

Measured in open (4 pi) space at 2 metres with 2.83 V input, using band limited pink noise, then

referred to 1 metre.

(4)

Calculated at 1 m.

(5)

Measured in open (4 pi) space at 2 metres.

CDD5

CDD6

CDD8

TYPE

Ultra-compact, Coaxial Differential

Dispersion passive two-way system

Ultra-compact, Coaxial Differential

Dispersion passive two-way system

Ultra-compact, Coaxial Differential

Dispersion passive two-way system

FREQUENCY RESPONSE

100 Hz-20 kHz ± 3 dB,

-10 dB @ 70Hz

80 Hz-20 kHz ± 3 dB,

-10 dB @ 70 Hz

70 Hz-20 kHz ± 3 dB,

-10 dB @ 55 Hz

DRIVER

LF: 5.25” (130 mm)/1.25” (32 mm) voice

coil, long excursion, ferrite motor system

HF: 0.75” (19 mm) voice coil, fabric dome

with neodymium motor system

LF: 6.5” (165 mm)/1.5” (38 mm) voice

coil, long excursion, ferrite motor system

HF: 1” (25 mm) voice coil, fabric dome

with neodymium motor system

LF: 8” (200 mm)/2” (50 mm)

voice coil, long excursion, shared ferrite

motor system with HF

HF: 1” (25 mm) exit/1.4” (38 mm) voice

coil, polyimide dome compression driver

RATED POWER

100 W AES, 400 W peak

150 W AES, 600 W peak

200 W AES, 800 W peak

RECOMMENDED

AMPLIFIER

MA2.8Q, MA2.0

SENSITIVITY

90 dB

91 dB

94 dB

MAXIMUM SPL

110 dB continuous, 116 dB peak

113 dB continuous, 119 dB peak

117 dB continuous, 123 dB peak

NOMINAL IMPEDANCE

8 ohms

DISPERSION (-6 dB)

120˚-90˚ horizontal, 80˚ vertical (user-

rotatable)

110˚-80˚ horizontal, 80˚ vertical (user-

rotatable)

110˚-80˚ horizontal, 60˚ vertical (user-

rotatable)

CROSSOVER

2.5 kHz passive

2.3 kHz passive

ENCLOSURE

3 litre, ABS

9 litre, composite material

14 litre, composite material

FINISH

Black or white

Black or white textured paint

PROTECTIVE GRILLE

Standard models only: black or white

perforated steel with scrim cloth backing

“WR” models only: black or white

perforated, zinc-plated steel with scrim

cloth backing, Declon® synthetic fabric

layer and inner, zinc-plated, hydrophobic

steel mesh layer

Standard models only: black or white

perforated steel with scrim cloth backing

“WR” models only: black or white

perforated, zinc-plated steel with scrim

cloth backing, Declon® synthetic fabric

layer and inner, zinc-plated, hydrophobic

steel mesh layer

Standard models only: black or white

perforated steel with scrim cloth backing

“WR” models only: black or white

perforated, zinc-plated steel with scrim

cloth backing, Declon® synthetic fabric

layer and inner, zinc-plated, hydrophobic

steel mesh layer

CONNECTORS

Low-profile 13 A push-lock

WR models only: weatherproof cover with

gasket seal and cable gland

Low-profile 13 A push-lock

WR models only: weatherproof cover with

gasket seal and cable gland

Low-profile 13 A push-lock

WR models only: weatherproof cover with

gasket seal and cable gland

PIN CONNECTIONS

Left to right: Input+, Input -, Link -, Link +

FITTINGS

6 x M5 inserts for wall/ceiling brackets

4 x M6 inserts for wall/ceiling brackets

6 x M6 inserts for wall/ceiling brackets

ENVIRONMENTAL

IP54 (Model CDD5TX-WR only)

IP54 (Model CDD6TX-WR only)

IP54 (Model CDD8-WR only)

DIMENSIONS

(W) 160 mm x (H) 230 mm x (D) 149 mm

(W) 6.3 in x (H) 9.1 in x (D) 5.9 in

(W) 210 mm x (H) 325 mm x (D) 210 mm

(W) 8.3 in x (H) 12.8 in x (D) 8.3 in

(W) 256 mm x (H) 410 mm x (D) 253 mm

(W) 10.1 in x (H) 16.1 in x (D) 10 in

WEIGHT

2.7 kg (6 lb)

5 kg (11 lb)

9.5 kg (21 lb)

ACCESSORIES

CDDCB5B ceiling bracket black

CDDCB5W ceiling bracket white

CDDWB6/8B wall bracket black

CDDWB6/8W wall bracket white

CDDCB6/8B ceiling bracket black

CDDCB6/8W ceiling bracket white

CDDWB6/8B wall bracket black

CDDWB6/8W wall bracket white

CDDCB6/8B ceiling bracket black

CDDCB6/8W ceiling bracket white

Содержание CDD Series

































































Результаты поиска

Содержание CDD Series

Отзывы:

Похожие инструкции для CDD Series

Бренды по названию

Популярные бренды

Martin Audio CDD Series, Руководство пользователя

Результаты поиска

Содержание CDD Series

Отзывы:

Похожие инструкции для CDD Series

Бренды по названию

Популярные бренды