Martel MC1000 Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 28

Martel MC1000 Скачать руководство пользователя страница 9

and acts as a second function
key to all keys that have an
associated second function.
Features such as setpoints,
°F/°C, backlight and external
pressure module activation all
use the Shift key.

B. Setpoints

1. Storing Setpoints

The setpoint mode allows up to 9 set-
points to be stored in non-volitile memo-
ry for each range. The procedure is as
follows:
a. Set the output to the desired value.
b. Press shift followed by the “SET” key.
c. Choose the desired setpoint storage

location by pressing a key (1-9).

d. Enter a new value and repeat steps 1

thru 3 as needed, up to 9 setpoints for
each range can be stored.

2. Recalling Setpoints

a. To recall a setpoint, press shift fol-

lowed by the”SPT” key.

b. You will be prompted to enter the

number of the desired setpoint loca-
tion stored previously.

c. Press the desired location number and

the unit will go to that output.

3. Automated Stepping

The MC1000 can auto-step through
some or all of the stored setpoints for a
given range. The procedure is as follows:
a. Press “Shift” followed by auto.
b. “Auto SPT ?” will appear. Enter the

7

«
...
7
8
9
10
11
...
»

Содержание MC1000





























Отзывы:

Нет отзывов