Martel MC1000 Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 28

Martel MC1000 Скачать руководство пользователя страница 5

3

Off

On

Canadian Standards Association

The following definitions apply to the terms
“Warning” and “Caution”.
• “Warning” identifies conditions and actions

that may pose hazards to the user.

• “Caution” identifies conditions and actions

that may damage the instrument being used.

Use the calibrator only as specified in this man-
ual, otherwise injury and damage to the calibra-
tor may occur.

Warning

To avoid possible electric shock or

personal injury:

• Do not apply more than the rated voltage.

See specifications for supported ranges.

• Follow all equipment safety procedures.
• Never touch the probe to a voltage source

when the test leads are plugged into the cur-
rent terminals.

• Do not use the calibrator if it is damaged.

Before you use the calibrator, inspect the
case. Look for cracks or missing plastic. Pay
particular attention to the insulation surround-
ing the connectors.

• Select the proper function and range for your

measurement.

• Make sure the battery cover is closed and

latched before you operate the calibrator.

«
...
3
4
5
6
7
...
»

Содержание MC1000





























Отзывы:

Нет отзывов