Marson MT581W Скачать руководство пользователя страница 28 | Manualshive

Страница: 28 / 201

Marson MT581W Скачать руководство пользователя страница 28

Enter Setup

Sensitivity (Sense Mode)

Sensitivity specifies the degree of acuteness of MT581W’s response to changes in images captured. There are 20 levels
to  choose  from. The  smaller  the  value,  the  higher  the  sensitivity  and  the  lower  requirement  in  image  change  to  trigger
MT581W.  You  can  select  an  appropriate  degree  of  sensitivity  that  fits  the  application  environment.  This  feature  is
only  applicable to the Sense mode.

Low Sensitivity

Medium Sensitivity

High Sensitivity

**

Enhanced Sensitivity

Custom Sensitivity

(Level 1-20)

Set the sensitivity to Level 10:

1. Scan the

Enter Setup

barcode.

2. Scan the

Custom Sensitivity

barcode.

3. Scan the numeric barcodes “1” and “0” from the “Digit Barcodes” section in Appendix.

4. Scan the

Save

barcode from the “Save/Cancel Barcodes” section in Appendix.

5. Scan the

Exit Setup

barcode.

** Exit Setup

«
...
26
27
28
29
30
...
»

Содержание MT581W










































































































































































































Отзывы:

Нет отзывов