Marson MT581W Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 201

Marson MT581W Скачать руководство пользователя страница 25

Enter Setup

Reread Timeout

Reread Timeout can avoid undesired rereading of same barcode in a given period of time. This feature is only applicable to
the Sense and Continuous modes.

Enable Reread Timeout:

Do not allow MT581W to reread same barcode before the reread timeout expires.

Disable Reread Timeout:

Allow MT581W to reread same barcode.

Enable Reread Timeout

** Disable Reread Timeout

The following parameter sets the time interval between two successive reads on same barcode. It is programmable in 1ms
increments from 0ms to 3,600ms. When it is set to a value greater than 3,000, the timeout for rereading same programming
barcode is limited to 3,000ms. The default setting is 1500ms.

Set Reread Timeout

Set the reread timeout to 1,000ms:

1. Scan the

Enter Setup

barcode.

2. Scan the

Set Reread Timeout

barcode.

3. Scan the numeric barcodes “1”, “0”, “0” and “0” from the “Digit Barcodes” section in Appendix.

4. Scan the

Save

barcode from the “Save/Cancel Barcodes” section in Appendix.

5. Scan the

Exit Setup

barcode.

** Exit Setup

«
...
23
24
25
26
27
...
»

Содержание MT581W










































































































































































































Отзывы:

Нет отзывов