MARS COMMERCE SOLO-NX Скачать руководство пользователя страница 5

Страница: 5 / 35

SOLO-NX

INSTALLATION MANUAL

Page 5

START UP

VERY

IMPORTANT

USE A

MICRO SIM CARD

(micro-SIM, see the picture



)

WITH MEMORY FOR UP TO 250 CONTACTS!



Insert SIM card to be used for SOLO-NX in your personal mobile phone.

IMPORTANT

ERASE THE PIN CODE!



Insert SIM card in SOLO-NX device. The unit must be switched OFF when you insert the
SIM!



Connect inputs and outputs to SOLO-NX.



Connect the antenna to antenna connector.



Connect power cable to SOLO-NX device



Connect device to source power supply voltage.



Wait until LED3 display is turned ON (Yellow) and LED1 (Blue) starts flashing. This is set
in around 30 – 45 seconds.



SOLO-NX unit is now ready to operate.

IMPORTANT

Before sending any SMS commands to SOLO-NX device, SOLO-NX must
be in normal operation!

NOTE

SOLO-NX device will “beep” in 15s interval until the device is not in normal
operation.

Содержание SOLO-NX




































Результаты поиска

Содержание SOLO-NX

Отзывы:

Бренды по названию

Популярные бренды

MARS COMMERCE SOLO-NX, Инструкция по эксплуатации

Результаты поиска

Содержание SOLO-NX

Отзывы:

Бренды по названию

Популярные бренды