MARMON ANGELO PO COMBISTAR FX Скачать руководство пользователя страница 29

Страница: 29 / 178

Copyright by Servizio Clienti ANGELO PO Spa

How to configure the type of oven

The setup process of the oven must be done after replacing one of the following

components: CPU board, power board, inverter, combustion control board. It is required to

make all the boards communication with one another and to select the correct operating

parameters of the oven.

Operate as follow:

- Enter the service menu

- Select the "oven type"

- Select the type of oven

- Wait until the end of the procedure and check the list of devices in comparison with

the table below.

- If you get the alarm E20 during the procedure, reset with the reset button and

repeat the procedure by pressing the function "repeat configuration”. If the problem

persists, verify the items found and control the wiring of the components not

detected.

- If at the end of the procedure, the screen does not match the table below, check the

wiring and repeat the configuration by pressing "repeat configuration”.

- If the configuration is correct (the screen corresponds to the table) press "OK".

Alarm log:

Selecting this voice you get the list of the last thirty alarms that have occurred

on the oven. The list will show you the alarm code, date and time.

Содержание ANGELO PO COMBISTAR FX



















































































































































































Результаты поиска

Содержание ANGELO PO COMBISTAR FX

Отзывы:

Похожие инструкции для ANGELO PO COMBISTAR FX

Бренды по названию

Популярные бренды

MARMON ANGELO PO COMBISTAR FX, Техническое руководство

Результаты поиска

Содержание ANGELO PO COMBISTAR FX

Отзывы:

Похожие инструкции для ANGELO PO COMBISTAR FX

Бренды по названию

Популярные бренды