Marlo Incorporated MR Series Скачать руководство пользователя страница 2 | Manualshive

Страница: 2 / 52

Marlo Incorporated MR Series Скачать руководство пользователя страница 2

MR 150M–1050M - PLC CONTROLLER

Please Circle and/or Fill in the Appropriate Data for Future Reference:

Softener Model:

MR _____________

System Size:

Single

/

Twin

/

Triple

/

Quad

Meter Size:

________________

Configuration: Timeclock

/

Twin Alt

/

Parallel

/

Progressive

Unit Capacity:

________________ Grains

Feed Water Hardness:

________________ Grains

Treated Water:

________________ Gallons/Liters

BW/Regen Time

________________ AM/PM or OFF

Additional Notes: ________________________________________________________

______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________

IMPORTANT PLEASE READ:

�

Warranty of this product extends to manufacturing defects.

�

The information, specifications and illustrations in this manual are based on the latest

information available at the time of printing. The manufacturer reserves the right to make

changes at any time without notice.

�

This product should be installed by a plumbing professional on potable water systems only.

�

This product must be installed in compliance with all local and state and municipal plumbing and

electrical codes. Permits may be required at the time of installation.

�

If operating pressure exceeds 100 psi a pressure reducing valve must be installed. If operating

pressure drops below 30 psi a booster pump must be installed.

�

Do not install the unit where temperatures may drop below 32°F or rise above 100°F.

�

A prefilter should be used on installations in which free solids are present.

�

A constant voltage of 120V/60Hz (unless otherwise specified) must be supplied to the controller

to maintain proper function.

�

Union or flange fittings are recommended at the control valve's inlet, outlet, and drain

connections

�

If distance of drain line is over a 10 ft. vertical or 25 ft. horizontal run, increase drain line one

pipe size over that provided on the control valve.

�

Do not make a direct connection to the drain. Provide an air gap of at least four times the

diameter of the pipe to conform to sanitation codes and to permit observation of the flow.

Page 1

MR 150M–1050M PLC

«
1
2
3
4
...
»

Содержание MR Series





















































Отзывы:

Нет отзывов