1. Legal information
1.1 Declaration of compliance
The manufacturer, MARK Save A Life GmbH, Gleinkerau
23, 4582 Spital am Pyhrn, Austria, hereby declares that the
product described below, “MARK Secure 2”, complies with
the requirements formulated in EN 795:2012 anchor point
type A, which is also the subject of the inspection report
number ZP/B141/17-R1.
Type approval testing by: DEKRA Exam GmbH,
Dinnendahlstraße 9, 44809 Bochum, Germany.
1.2 Labelling
Your product is labelled with a batch number.
Assign your product an inventory number and enter it in the
installation report.
Do not remove any labels from your product!
Manufacturer
Product standard
Personal authorisation
Type designation
Year of manufacture
1.3 Exclusion of product liability
We accept no liability for direct, indirect or accidental
consequences, nor any type of damage arising from the
use of this product or from incorrect information provided
by the competent inspector or installation engineer on the
installation report or the inspection report.
1.4 Copyright notice
The layout, graphics, pictograms and photographs, as well
as all other text and image content found in this instruction
manual are protected by copyright.
2. Use
Activities that require use of this product can often be
dangerous. Therefore observe the safety notices. Please
contact our customer service if you have any doubts or find
the information difficult to understand. Ensure that the fall
space is calculated so that in the event of a fall you do not
hit an obstacle or impact on the floor.
Protect the product from sharp-edged objects,
welding sparks, sources of fire, chemicals, oils,
acids, etc.
Draw up a rescue plan that includes the sequence
and the execution of rescue measures.
2.1 Intended use
This product may only be used for the purpose described
in this instruction manual (see Point 2.1.1) and only in
conjunction with tested and approved components. It must
not be combined with other components, as this could put
your safety at risk. MARK Secure 2 must be used with
Knauf system components or with similar products with the
same properties.
You may only use this product if you are physically and
mentally capable of doing so, i.e., for example, not if you
are under the influence of drugs or alcohol, are suffering
from mental strain or have other mental or physical
impairments. In any case, the intended use as protection
against a fall from height requires full physical and mental
aptitude.
2.1.1 Purpose of the product as an anchor device
according to EN 795:2012 type A
The product may be used within the intended use conditions
on the specified wall and attachment shell systems from
Knauf Gesellschaft m.b.H., or similar products with the
same properties, for the intended purpose as protection
against a fall from height.
Note:
This product is an anchor device, the purpose of which
is to protect the user from a fall from height, either by
preventing a fall (restraint system) or by arresting a
free fall (fall arrest system).
The MARK Secure 2 anchor point is intended for use as
an anchor device in conjunction with personal protective
equipment (PPE) recommended by MARK Save A Life
GmbH (retractable fall arrest blocks, safety overalls and
connectors from MARK Save A Life).
Classed as tested accessories: Test standard
Descender and rescue devices
Lifting devices
Retractable fall arrest blocks
Guided-type fall arresters on
flexible anchor lines
Energy absorbers
Carabiners
Safety harnesses
Safety nets
EN 341
EN 1496
EN 360
EN 353-2
EN 355
EN 362
EN 361
EN 1263
If it seems unsafe to continue using this product, (see Point
8.1) you must not use it again under any circumstances.
Before every use of the product, the user must carry out
a visual inspection according to Point 7 of this manual to
ensure that the product is in serviceable condition.
2.1.2 Use of the anchor point
In order to use the anchor point, the buckle is released
from the lock and folded up. The connector of the PPE can
be suspended.
In principle, the load from a fall from height may be in any
direction protruding from the wall surface or parallel to the
wall.
The total position change of the anchor point to be
expected in the event of a fall from height (consisting of
the deformation of the metal stud partition or attachment
shell and the anchor point itself) is a maximum of 15 cm
in the event of a vertical load direction parallel to the wall
surface.
If there is a fall-related load when a person falls vertically
to the wall surface (e.g. in the event of an unintentional
redirection of the load), it must be anticipated that there will
be a total position change of the anchor point (consisting
of the deformation of the metal stud partition or attachment
shell and the anchor point itself) of a maximum of 15% of
the respective wall height.
In principle, the product may be installed at any position
of the specified Knauf or similar metal stud partitions and
attachment shells that is selected as being sensible for the
intended use.
2. Fold up buckle
Working position
3. Fold buckle down
after use
4. Move buckle into lock
1. Move buckle out of lock
4
5
Read instruction manual
Batch number
CE marking