dead battery is the degradation of your viewing image.
Try charging your battery or if the battery is unable to hold
a charge, replace it with a new one of the same specifica-
tion. If you need to remove the battery, unplug the two battery
terminals from the battery. Unscrew both the screws located
in the upper right and left corner of the battery compartment.
This will allow you to remove the battery strap from the
battery. After removing the strap, lift the battery up slightly
with a finger on either side of the battery and slide the
battery towards you. This should allow for easy removal of
the battery. To replace the battery, lift the battery up and slide
into the battery compartment until the front of the battery
drops down into the compartment.
Product Performance Specifications
Battery
. . . . . . . . . . . . . . . . . . 12 volt DC, 7 Amp hr.
Charger
. . . . . . . . . . . . . . . . . 12 volt DC, 500 mA
Camera
. . . . . . . . . . . . . . . . .
Image Sensor. . . . . . . . 1/3" Sony SUPER HAD CCD (B/W)
Resolution . . . . . . . . . . 400 horizontal lines
Light Sensitivity . . . . . . 0 lux with lights on
Field of View. . . . . . . . . 90 degrees
Monitor
. . . . . . . . . . . . . . . . .
CRT . . . . . . . . . . . . . . . 5.5" (diag.) flat screen
high resolution
Current Draw
. . . . . . . . . . . . .
On (no lumination) . . . . 700 mA
Lights On . . . . . . . . . . . 800 mA
facing forward you’re now able to clip the camera onto the
downrigger cable swivel just above the ball. Rotate the cam-
era to the back side (location of fin) and view out the back as
you’re pulling the camera forward. This allows the fin to act
as the rudder and stabilize the camera while tracking through
the water. Stainless screws are provided to attach the strap
or additional ballast weight. When using the additional ballast
weight, be careful to keep the camera out of heavy weeds,
brush, or large rocks. If the camera becomes hung up, back
up from the direction you were traveling and slowly try to
back the camera out of the snag. Do NOT pull upward with
force unless all other avenues have been pursued.
BATTERY CHARGING
Recharging the battery after every use is recommended.
As a general rule of thumb, charge the battery for twice the
amount of time as it was used. The VS460 underwater view-
ing system has a DC charging port located just above the
battery door on the right side of the monitor face. The charger
that was supplied with the VS460 system is a 500 mA DC
charger with a male jack. To charge your system, simply plug
the male jack of the charger into the plug in port in the face
of the monitor and then plug the charger into a 110 volt AC
wall outlet. The 7 amp, 12 volt battery that was supplied with
the VS460 system should take about 15 hours to charge from
a completely discharged state. The charger incorporates a
Charge Alert feature to alert the user to when the battery
reaches full capacity. This is accomplished when the green
LED light shuts off on the face of the charger. The charger
does not shut off automatically but will output a trickle charge
indefinitely. It is recommended, however, that the charger be
disconnected from the monitor when the Charge Alert green
LED is no longer on. It’s recommended that you remove the
battery door while charging to allow for increased air ventila-
tion through out the battery compartment.
If your viewing image appears cloudy or fuzzy, check your
battery charge. One of the major symptoms of a dead or near
6
7
Содержание VS460
Страница 1: ...USER MANUAL 460 460 ...
Страница 7: ......
