ENGLISH
11
Front left and right speakers
We recommend to set the front L and R speakers
with 45-60 degrees from the listening position.
Center speaker
We recommend to set the front line of the center
speaker with the front L/R speakers.
Surround left and right speakers include phantom
surround back speaker
Place the speakers right beside of the listening
position or a little backward.
Subwoofer
We recommend to use a subwoofer to have
maximum bass effect. Subwoofer bears only low
frequency range so you can place it vertically or
horizontally, anywhere in the room.
Note:
• Pay special attention for the following speakers
placements.
Surround L and Surround R Speakers.
Place the Surround Speaker L (SS2500SL)
to your left side and the Surround R Speaker
(SS2500SR) to your right side. Do not
interchange left and right.
Center Speaker
Lay the Center Speaker(SS2500C) on the
tray attached as an accessory.
Subwoofer
CONNECTIONS
PRECAUTIONS CONCERNING
CONNECTIONS
• Use only a 120V AC power source for ER2500U,
and a 230V AC power source for ER2500S.
Using any other power source could cause a fire
or electric shock.
• Always grasp the power plug when unplugging
or plugging in the power cord.
• Complete all connections before plugging in the
power cord.
• Be sure to make a distinction between the left
(white) and right (red) audio cable plugs when
connecting them.
• When connecting this unit to other audio
equipment, read the operation manual for that
equipment carefully for details on how to make
the correct connections.
CONNECTING 5.1/6.1CH SPEAKER SYSTEM
SS2500 (OPTIONAL)
The 5.1/6.1ch speaker system SS2500 consists of
the following speakers. (See the labels of each
speakers.)
• Front Speaker L/R (SS2500F) x 2
• Center Speaker (SS2500C) x 1
• Surround L Speaker (SS2500SL) x 1
• Surround R Speaker (SS2500SR) x 1
• Subwoofer (SS2500SW) x 1
1.
Locate those speakers as shown below
.
2.
Connect Speaker to Unit. (
☞
p12)
Connect the speakers to the corresponding
speaker terminals of the ER2500 using colored
cords supplied.
CONNECTING SPEAKER CORD TO UNIT
1.
Push the terminal lever in the direction of the
arrow, and keep this condition.
2.
Insert the bare part of the cord into the hole in
the side of each terminal.
3.
Put the terminal lever back, and make sure it
is fastened securely by pulling the cord lightly.
1.
2.
3.
CONNECTING SPEAKER CORD TO 5.1/
6.1CH SPEAKER SYSTEM SS2500
1.
Loosen the knob by turning counterclockwise.
2.
Insert the bare part of the cord into the hole in
the side of each terminal.
3.
Tighten the knob by turning clockwise to secure
the cable.
1.
3.
2.
Caution:
• Be sure to use speakers with the specified
impedance shown on the rear panel of this
unit.
• To prevent damage to circuitry, do not let the
bare speaker cords touch each other and do
not let them touch any metal part of this unit.
• Do not touch the speaker terminals when the
power is on. It may cause electric shocks.
• Do not connect more than one speaker cord to
one speaker terminal. Doing so may damage
this unit.
Note:
• Be sure to connect the positive and negative
cords for the speaker properly. If they are
miss-connected, the signal phase will reversed
and the signal quality will be corrupted.
SPECIAL INSTRUCTION FOR SURROUND
L AND SURROUND R SPEAKERS.
The upper two terminals are for the Surround Back
connection for both Surround L (SS2500SL) and
Surround R (SS2500SR) speakers.
Connect the brown cord supplied (separation cord
for Surround Back) referring the label on rear of the
cabinet.
Sub
woofer
Front
Left
Center
Front
Right
Surround-Left
Surround-Right
Phantom
Surround-
Back
Tray
Approx. 40˚
Cushion
• Vertical Setting
• Horizontal Setting
ER2500U DFU̲01̲eng1/4
04.8.26, 4:29 PM
Page 11
Adobe PageMaker 6.5J/PPC
