Mar Cor Purification MILLENIUM HX Скачать руководство пользователя страница 72 | Manualshive

Страница: 72 / 158

Mar Cor Purification MILLENIUM HX Скачать руководство пользователя страница 72

Millenium HX RO System

3030226 Rev. D

4-20

Screen Operation And Specifications

4.4

Alarm Screens

Screen Titles: Alarms

Screen Description:

This screen is displayed indicating that a component within the
RO has failed along with a possible error code. Refer to Section
6.9

“

Service Required Component Failure Detected

”

for the error

code list.

This device has a tilt sensor to prevent operation in a horizontal
orientation. If the device is placed on its side, operation of the
device ceases and it cannot be started until the RO is placed in an
upright position.

This  device  has  a  product  water  temperature  sensor  that  is
integral  to  the  conductivity  probe.    If  the  product  water
temperature  exceeds  105°F  (41°C),  the  RO  will  shut  down  and
cannot be restarted in run until the product water sensor is stable
below 105°F (41°C).

This  device  has  a  pressure  transducer  that  monitors  the  pump
outlet  pressure.    If  pump  pressure  exceeds  240  PSI,  or  is  20  PSI
below the  target  pressure, the RO will shut down.  The pressure
alarm settings are not user adjustable.

During  the  heat  process,  pump  pressure  is  monitored  and  if  the
pressure  goes outside of a  factory set  range, the Pump Pressure
Alarm will sound.  These settings are not user settable.

«
...
70
71
72
73
74
...
»

Содержание MILLENIUM HX































































































































































Отзывы:

Нет отзывов