MANN+HUMMEL ProVent 100 Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 29

MANN+HUMMEL ProVent 100 Скачать руководство пользователя страница 6

MANN + HUMMEL ProVent

MANN+HUMMEL Industrial Filters

6

Pos.

Name

Pos.

Name

1

Lid with integrated pressure control valve

8

Outlet

2

Oil separating element

9

Seal of blow-by inlet

3

Housing

10

Seal of lid/housing

4

Pressure relief valve/bypass valve

11

Pressure control valve

5

Holder

12

Seals of element

6

Oil return

13

Quick-connect couplings

7

Inlet

14

Lid with integrated pressure relief valve

4 Assembly

4.1 General

information

Check that the scope of delivery is complete
and that there are no signs of damage.

If parts delivered are damaged, please inform
MANN+HUMMEL immediately.

The assembly of the ProVent and the
installation of the lines may only be
carried out by qualified persons
instructed for this purpose.

It is essential to observe the
information on correct assembly when
completing assembly and installation
work.

When working on the fuel supply,
always place collecting vessels under
the tank or lines to collect any
escaping fuel. Dispose of collected
fuel or oil in accordance with the
respective applicable local waste
disposal directives.

Pay attention to the direction of flow.

Carry out fixations conscientiously.

Health hazard due to escaping oil!

Wear safety goggles and gloves.

(Also refer to the material safety data
sheet for diesel fuel)

«
...
4
5
6
7
8
...
»

Содержание ProVent 100






























Отзывы:

Нет отзывов