Manitowoc MARINE MODEL S1800 страница 78 Скачать руководство пользователя

Страница: 78 / 100

Refrigeration System

Section 7

7-12

Part Number 80-1634-3

ANALYZING DISCHARGE PRESSURE

DURING FREEZE OR HARVEST CYCLE

Procedure

1. Determine the ice machine operating conditions:

Air temp. entering condenser

______

Air temp. around ice machine

______

Water temp. entering sump trough

______

2. Refer to Operating Pressure Chart for ice machine

being checked.

Use the operating conditions determined in step 1 to
find the published normal discharge pressures.

Freeze Cycle _______

Harvest Cycle _______

3. Perform an actual discharge pressure check.

4. Compare the actual discharge pressure (step 3) with

the published discharge pressure (step 2).

The discharge pressure is normal when the actual
pressure falls within the published pressure range for the
ice machine’s operating conditions.

Freeze Cycle Discharge Pressure High Checklist

Freeze Cycle Discharge Pressure Low Checklist

NOTE: Do not limit your diagnosis to only the items listed in the checklists.

Freeze Cycle

PSIG (kPa)

Harvest Cycle

PSIG (kPa)

Beginning of Cycle

__________

Middle of Cycle

__________

End of Cycle

__________

Possible Cause

Check/Correct

Improper installation

See “Installation/Visual Inspection Checklist”

Restricted condenser water flow

Low water pressure [20 psi (138 kPa) min.]
High inlet water temperature (90°F/32.2°C max.)
Dirty condenser
Dirty/defective water regulating valve
Water regulating valve out of adjustment

Improper refrigerant charge

Overcharged
Non-condensables in system
Wrong type of refrigerant

Other

Non-Manitowoc components in system
High side refrigerant lines/component restricted (before mid-condenser)

Possible Cause

Check/Correct

Improper installation

See “Installation/Visual Inspection Checklist”

Improper refrigerant charge

Undercharged
Wrong type of refrigerant

Water regulating valve

Out of adjustment
Defective

Other

Non-Manitowoc components in system

Содержание MARINE MODEL S1800





































































































Результаты поиска

Содержание MARINE MODEL S1800

Отзывы:

Похожие инструкции для MARINE MODEL S1800

Бренды по названию

Популярные бренды

Manitowoc MARINE MODEL S1800, Руководство по обслуживанию

Результаты поиска

Содержание MARINE MODEL S1800

Отзывы:

Похожие инструкции для MARINE MODEL S1800

Бренды по названию

Популярные бренды