Manitowoc MARINE MODEL S1800 Скачать руководство пользователя | Manualshive

Страница: 79 / 100

background image

Section 7

Refrigeration System

Part Number 80-1634-3

7-13

ANALYZING SUCTION PRESSURE

DURING FREEZE CYCLE

The suction pressure gradually drops throughout the
freeze cycle. The actual suction pressure (and drop rate)
changes as the air and water temperatures entering the
ice machine change. This affects freeze cycle times.

To analyze and identify the proper suction pressure drop
throughout the freeze cycle, compare the published
suction pressure to the published freeze cycle time.
“Operating Pressure” and “Freeze Cycle Time” charts
can be found later in this section.

NOTE: Analyze discharge pressure before analyzing
suction pressure. High or low discharge pressure may
be causing high or low suction pressure.

Procedure

Step

Example Using SY1004A Model Ice Machine

1.

Determine the ice machine operating

conditions.

Air temp. entering condenser:

90°F/32.2°C

Air temp. around ice machine:

80°F/26.7°C

Water temp. entering water fill valve:

70°F/21.1°C

2A.

Refer to “Cycle Time” and “Operating

Pressure” charts for ice machine model being
checked. Using operating conditions from Step
1, determine published freeze cycle time and
published freeze cycle suction pressure.

Published freeze cycle time:

Published freeze cycle suction pressure:

8.5 - 9.8 minutes

58-28 PSIG

2B.

Compare the published freeze cycle time

and published freeze cycle suction pressure.
Develop a chart.

Published Freeze Cycle Time (minutes)

Published Freeze Cycle Suction Pressure (psig)

3.

Perform an actual suction pressure check at

the beginning, middle and end of the freeze
cycle. Note the times at which the readings are
taken.

Beginning of freeze cycle:

70 PSIG at 1 minute

Middle of freeze cycle:

57 PSIG at 7 minutes

End of freeze cycle:

40 PSIG at 14 minutes

4.

Compare the actual freeze cycle suction

pressure (Step 3) to the published freeze cycle
time and pressure comparison (Step 2B).
Determine if the suction pressure is high, low
or acceptable.

Time Into

Freeze Cycle

Published

Pressure

Actual

Pressure

Result

1 minutes
5 minutes

10 minutes

58 PSIG
43 PSIG
28 PSIG

70 PSIG
48 PSIG
40 PSIG

High
High
High

1

3

5

8

10

58

52

43

33

28

«
...
77
78
79
80
81
...
»

Содержание MARINE MODEL S1800





































































































Отзывы:

Нет отзывов

Похожие инструкции для MARINE MODEL S1800

Бренд: Panasonic Страницы: 44

Бренд: Unic Страницы: 2

Бренд: Oster Страницы: 46

CafeRomatica 960

Бренд: Nivona Страницы: 30

Бренд: U-Line Страницы: 48

Бренд: Wilfa Страницы: 44

Бренд: Dolce Gusto Страницы: 20

Бренд: TEFAL Страницы: 56

Бренд: Scotsman Страницы: 29

Бренд: Galanz Страницы: 7

Бренд: A&D Страницы: 22

SkyCoffee RCM-M1509S-A

Бренд: Redmond Страницы: 16

Бренд: Klarstein Страницы: 64

FlexBrew Advanced 5-in-1

Бренд: Hamilton Beach Страницы: 36

Бренд: Royal Страницы: 28

Бренд: Blueair Страницы: 40

Бренд: Klarstein Страницы: 56

Бренд: SPM Страницы: 76

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды